Note : - Welltech Computer Co., Ltd
Note : - Welltech Computer Co., Ltd Note : - Welltech Computer Co., Ltd
Figure 18. Disconnect tone table.WellGate 2680 supports an alternative feature to release FXO port by detection LoopCurrent Drop signal. Go to Advanced Configuration System Setting DisconnectSignal Detection to select Loop Current Drop feature. Once calling user drop this call,PSTN or PABX may drop Loop Current signal for about 300 msec (default setting) toinform FXO interface. To detect Loop current drop duration can be changed. See Figure19. Go to Advanced Configuration System Setting Disconnect SignalDetection to select Loop Current Drop feature and Current Drop Time. This featuredepends on the PSTN switch or PABX you are using.Figure 19. Loop Current Drop detection at FXO18Welltech Technology Co., Ltd. Released Version 1.0
7. FLASH command generation and detection on FXO and FXS gateway.FLASH feature is widely used for PABX extension to implement PABX’s advancedfeatures such as Call Transfer, Call Hold, Conference, Forwarding or Call Park andothers. PABX relies on extension’s analog phone set to generate Flash time to informPABX this is an FLASH command.In this FXO+FXS P2P Hotline application, FXS needs to detect a FLASH commandfrom analog phone set and transmit to FXO gateway via VoIP network. Then, FXOgenerates an equivalent Flash time to PABX. Here are step to step guidance to configurethis function at both FXO and FXS gateway.Step 1 : Setup FXS Flash detection time range.Since FLASH command was initialized from analog phone set, check what flash timethis phone set can generate. Then, configure FXS gateway flash time detection range.See Figure 20 as follows. Go to Advanced Configuration Tone Setting setupMinimum and Maximum Flash Time range. Note : the analog phone flash timeshould be located inside FXS gateway setting range to detect an Flash commandcorrectly. Once FXS detect this command, it sends this signal to FXO gateway via SIPIP protocol automatically.Figure 20. Setup FXS Flash detection time range.Step 2 : Setup FXO Flash time generation.Go to Advanced Configuration System Setting Disconnect Signal Detection 19Welltech Technology Co., Ltd. Released Version 1.0
- Page 1 and 2: WellGate 2608 ( 8-FXS ) and WellGat
- Page 3 and 4: WellGate 2608 (8-FXS Gateway ) info
- Page 5 and 6: Step 4: Go to Line Setting webpage
- Page 7 and 8: Enter HOT LINE TEL field to 26808 w
- Page 9 and 10: Figure 7. Configure FXS Routing tab
- Page 11 and 12: as follows.TEL No : 26801User ID :
- Page 13 and 14: Figure 11. FXO Line Configuration.F
- Page 15 and 16: Figure 14. Ring Cadence of FXO Gate
- Page 17: Figure 17. Select Caller ID number
- Page 21: 21Welltech Technology Co., Ltd. Rel
7. FLASH command generation and detection on FXO and FXS gateway.FLASH feature is widely used for PABX extension to implement PABX’s advancedfeatures such as Call Transfer, Call Hold, <strong>Co</strong>nference, Forwarding or Call Park andothers. PABX relies on extension’s analog phone set to generate Flash time to informPABX this is an FLASH command.In this FXO+FXS P2P Hotline application, FXS needs to detect a FLASH commandfrom analog phone set and transmit to FXO gateway via VoIP network. Then, FXOgenerates an equivalent Flash time to PABX. Here are step to step guidance to configurethis function at both FXO and FXS gateway.Step 1 : Setup FXS Flash detection time range.Since FLASH command was initialized from analog phone set, check what flash timethis phone set can generate. Then, configure FXS gateway flash time detection range.See Figure 20 as follows. Go to Advanced <strong>Co</strong>nfiguration Tone Setting setupMinimum and Maximum Flash Time range. <strong>Note</strong> : the analog phone flash timeshould be located inside FXS gateway setting range to detect an Flash commandcorrectly. Once FXS detect this command, it sends this signal to FXO gateway via SIPIP protocol automatically.Figure 20. Setup FXS Flash detection time range.Step 2 : Setup FXO Flash time generation.Go to Advanced <strong>Co</strong>nfiguration System Setting Disconnect Signal Detection 19<strong>Welltech</strong> Technology <strong>Co</strong>., <strong>Ltd</strong>. Released Version 1.0
Change language