EFIS-D60 Installation Guide - Dynon Avionics

More documents

Recommendations

Info

EFIS Calibration and ConfigurationObtaining Magnetic Inclination and Intensity1. Browse to web page: www.dynonavionics.com/docs/maginfo.html. (Looking up thisinformation does not have to be done on a computer at the plane, with live Internetaccess.)2. The Dynon Avionics “Magnetic Inclination and Intensity” web page is updated asneeded; it contains a link to a NOAA web pages and instructions for easily finding yourlocal magnetic inclination and intensity by inputting your ZIP code (in the US) or yourlatitude and longitude and inputting the resulting data into your Dynon EFIS.3. Follow the instructions listed on the web page, especially clicking the “ComputeMagnetic Field Values” button at the bottom of the linked page – the values required byyour Dynon EFIS will be displayed only after clicking that button.Entering inclination and intensity into the EFIS-D601. Enter the inclination setup menu by pressing any button beneath an EFIS page (except thefar left or far right hotkeys), then SETUP > MAGINC2. Press INC or DEC to increment or decrement the displayed inclination angle. Press andhold to change values more rapidly.3. When the display shows the magnetic inclination angle for your location, press BACK toleave the menu.4. Enter the magnetic intensity setup menu by pressing any button beneath an EFIS page(except the far left or far right hotkeys), then SETUP > MAGINT5. Press SEL to change the digit being incremented or decremented. Press INC or DEC toincrement or decrement the selected digit. Press and hold to change values more rapidly.6. When the display shows the magnetic intensity for your location, press BACK to leavethe menu.4-2 EFIS-D60 Installation Guide
EFIS Calibration and ConfigurationEDC-D10A HEADING CALIBRATION (ON GROUND ONLY)The procedure for in-plane calibration of the EDC-D10A involves pointing the aircraft in fourdirections and taking data at each direction using the EFIS-D60. The EFIS-D60 will thenperform some calculations to ensure an accurate calibration.If you attempt a magnetic caibration without having performed the preceding section(Setting Magnetic Inclination Angle and Intensity), a warning message will be displayed:WARNING: MAGNETIC INCLINATION NOT SET.During magnetic calibration, do not turn the power off on the EFIS-D60. This will causeany recorded compass calibration data to be lost; the calibration will need to be restarted.To perform the calibration, you will need the following:1. EFIS-D60 and EDC-D10A installed in aircraft.2. Magnetic inclination angle and intensity properly entered into the EFIS-D60 per thesection above.3. An accurate method of aligning the aircraft with magnetic North, East, South, and West,such as an airport’s compass rose.Once you have the installation completed, have verified that your EDC-D10A communicateswith the EFIS-D60 (i.e., you see the heading tape displayed on the EFIS main page), and havelocated a suitable place to perform the calibration, perform the following steps:1. Turn on the EFIS-D60 and allow it to warm up for at least 15 minutes before performingthe calibration.2. Align the aircraft pointing magnetic North as closely as possible.3. On the EFIS-D60, enter the menu system by pressing any button beneath an EFIS page(except the far left or far right hotkeys) and press SETUP > MAGCAL. You should see amenu that reads NORTH, EAST, SOUTH, and WEST. If you do not, then the EDC-D10A is not properly communicating with your EFIS-D60.4. Press the NORTH button; you will see the message, COLLECTING DATA FORNORTH along with a 15 second timer. Let the time run out before proceeding.5. Align the aircraft pointing magnetic East as closely as possible.6. Press the EAST button; you will see the message, COLLECTING DATA FOR EASTalong with a 15 second timer. Let the time run out before proceeding.7. Align the aircraft pointing magnetic South as closely as possible.8. Press the SOUTH button; you will see the message, COLLECTING DATA FORSOUTH along with a 15 second timer. Let the time run out before proceeding.9. Align the aircraft pointing magnetic West as closely as possible.10. Press the WEST button; you will see the message, COLLECTING DATA FOR WESTalong with a 15 second timer. Let the time run out before proceeding.11. Press the END button. This will cause the EFIS-D60 to pause as it calculates. This pauseshould last between 1-20 seconds. However, if the collected data is poor, this can take asEFIS-D60 Installation Guide 4-3
Page 1: EFIS-D60Installation GuideThis prod
Page 5: Table of ContentsContact Informatio
Page 8 and 9: IntroductionAbout this GuideIn the
Page 10 and 11: Wiring Overview25-Pin Female EFIS H
Page 12 and 13: Wiring OverviewWIRING SYSTEM OVERVI
Page 14 and 15: Instrument Installation• All moun
Page 16 and 17: Instrument InstallationPC CONNECTIO
Page 18 and 19: Instrument InstallationSERIAL ALTIT
Page 20 and 21: Instrument InstallationPanel Locati
Page 23: 4. EFIS CALIBRATION AND CONFIGURATI
Page 27 and 28: 5. APPENDIXThe appendices contain a
Page 29 and 30: Alert Message Description End condi
Page 31 and 32: AppendixProblemAfter performing a m
Page 33 and 34: AppendixAppendix B: Dynon AOA/Pitot
Page 35 and 36: Appendixinstructions on the followi
Page 37 and 38: Appendixcontroller. Remember that e
Page 39 and 40: AppendixBoom mountPLUMBINGNOTE: Bec
Page 41 and 42: AppendixAppendix C: Encoder Serial-
Page 43 and 44: AppendixEFISDB25Pin#13Dynon EFIShar
Page 45: AppendixAppendix F: WeightsAdding a

EFIS-D60 Installation Guide - Dynon Avionics

Create successful ePaper yourself

Delete template?

Save as template?