Cisco AP541N Dual-band Single-radio Access Point Administration ...
Cisco AP541N Dual-band Single-radio Access Point Administration ... Cisco AP541N Dual-band Single-radio Access Point Administration ...
4WirelessModifying Advanced Settings81 Cisco AP 541N Dual-band Single-radio Access Point Quick Start Guide
WirelessModifying Advanced Settings4Different settings display depending on the mode you select. Table 19 describesthe fields and configuration options for the Advanced Settings page.Table 19FieldAdvanced Settings Field DescriptionsDescriptionStatus (On/Off)Specify whether you want the wireless radio on or off byclicking On or Off.If you turn off a wireless radio, the access point sendsdisassociation frames to all the wireless clients it wassupporting so that the wireless radio can be gracefullyshutdown and the clients can start the association processwith other available access points.NOTE: If Status is set to Off, then all fields are not able to beedited.ModeThe Mode defines the Physical Layer (PHY) standard usedby the wireless radio.NOTE: The modes available on your access point dependon the country code setting.Select one of the following modes for the wireless radiointerface:• 802.11a• 802.11b/g• 802.11a/n• 802.11b/g/n• 5 GHz 802.11n• 2.4 GHz 802.11nCisco AP 541N Dual-band Single-radio Access Point Quick Start Guide 82
- Page 33 and 34: StatusTraffic Statistics2Figure 7Vi
- Page 35 and 36: StatusAssociated Clients2Associated
- Page 37 and 38: StatusRogue AP Detection2Link Integ
- Page 39 and 40: StatusRogue AP Detection2Table 6Fie
- Page 41 and 42: StatusRogue AP Detection2Table 6Fie
- Page 43 and 44: 3SetupLAN SettingsThe default wired
- Page 45 and 46: 3Table 7 describes the fields to vi
- Page 47 and 48: SetupConfiguring 802.1X Authenticat
- Page 49 and 50: SetupEnabling the Network Time Prot
- Page 51 and 52: SetupEnabling the Network Time Prot
- Page 53 and 54: SetupEnabling the Network Time Prot
- Page 55 and 56: 4WirelessModifying Wireless Radio S
- Page 57 and 58: 4Table 10FieldModeRadio Settings Fi
- Page 59 and 60: WirelessModifying Virtual Access Po
- Page 61 and 62: WirelessModifying Virtual Access Po
- Page 63 and 64: WirelessModifying Virtual Access Po
- Page 65 and 66: WirelessModifying Virtual Access Po
- Page 67 and 68: WirelessModifying Virtual Access Po
- Page 69 and 70: WirelessModifying Virtual Access Po
- Page 71 and 72: WirelessModifying Virtual Access Po
- Page 73 and 74: WirelessModifying Virtual Access Po
- Page 75 and 76: WirelessModifying Virtual Access Po
- Page 77 and 78: WirelessModifying Virtual Access Po
- Page 79 and 80: WirelessClient Connection Control4C
- Page 81 and 82: WirelessClient Connection Control4T
- Page 83: WirelessModifying Advanced Settings
- Page 87 and 88: WirelessModifying Advanced Settings
- Page 89 and 90: WirelessModifying Advanced Settings
- Page 91 and 92: WirelessModifying Advanced Settings
- Page 93 and 94: WirelessModifying Advanced Settings
- Page 95 and 96: WirelessConfiguring the Wireless Di
- Page 97 and 98: WirelessConfiguring the Wireless Di
- Page 99 and 100: WirelessBandwidth Utilization4Bandw
- Page 101 and 102: WirelessConfiguring Quality of Serv
- Page 103 and 104: WirelessConfiguring Quality of Serv
- Page 105 and 106: WirelessConfiguring Quality of Serv
- Page 107 and 108: 5SNMPConfiguring SNMP on the Access
- Page 109 and 110: 5Table 25FieldSNMP Settings (Contin
- Page 111 and 112: SNMPConfiguring SNMP on the Access
- Page 113 and 114: SNMPConfiguring SNMP on the Access
- Page 115 and 116: SNMPConfiguring SNMP on the Access
- Page 117 and 118: SNMPConfiguring SNMP on the Access
- Page 119 and 120: SNMPSNMP Targets5NOTEAfter you conf
- Page 121 and 122: 6AdministrationAdministratorUse thi
- Page 123 and 124: 6Access Point ConfigurationThe acce
- Page 125 and 126: AdministrationAccess Point Configur
- Page 127 and 128: AdministrationSoftware Upgrade6The
- Page 129 and 130: AdministrationSoftware Upgrade6The
- Page 131 and 132: AdministrationEvent Logs6Click Refr
- Page 133 and 134: AdministrationEvent Logs6Configurin
4WirelessModifying Advanced Settings81 <strong>Cisco</strong> AP 541N <strong>Dual</strong>-<strong>band</strong> <strong>Single</strong>-<strong>radio</strong> <strong>Access</strong> <strong>Point</strong> Quick Start Guide