Cisco AP541N Dual-band Single-radio Access Point Administration ...
Cisco AP541N Dual-band Single-radio Access Point Administration ... Cisco AP541N Dual-band Single-radio Access Point Administration ...
PrefaceOnline Help, Supported Browsers, and LimitationsOnline help for the Access Point Configuration Utility pages provides informationabout all fields and features available from the Access Point Configuration Utility.The information in the online help is a subset of the information available in theAP541N Dual-band Single-radio Access Point Administration Guide.Online help information corresponds to each page on the Access PointConfiguration Utility.For information about the settings on the current page, click the Help link on theright side of a page.AP541N Dual-band Single-radio Access Point Administration Guide 5
1Getting StartedThe Cisco Access Point provides continuous, high-speed access betweenwireless devices and Ethernet devices. It is an advanced, standards-basedsolution for wireless networking in businesses of any size. The access pointenables wireless local area network (WLAN) deployment while providing state-ofthe-artwireless networking features.The access point operates in Standalone Mode. In Standalone Mode, the accesspoint acts as an individual access point in the network, and you manage it by usingthe Access Point Configuration Utility, or SNMP.This document describes how to perform the setup, management, andmaintenance of the access point in Standalone Mode. Before you power on a newaccess point, review the following sections to check required hardware andsoftware components, client configurations, and compatibility issues. Make sureyou have everything you need for a successful launch and test of your new orextended wireless network.This chapter contains the following topics:• Administrator Computer Requirements• Connecting the Access Point to a PC• Troubleshooting Your Connection• Configuring the Access Point by using the Getting Started Page• Verifying the Installation• Configuring Security on the Wireless Access PointTo manage the access point by using the Web interface, the access point needsan IP address. If you use VLANs or IEEE 802.1X Authentication (port security) onyour network, you might need to configure additional settings on the access pointbefore it can connect to the network.Cisco AP 541N Dual-band Single-radio Access Point Quick Start Guide 6
- Page 1 and 2: ADMINISTRATIONGUIDECisco Small Busi
- Page 3 and 4: ContentsNetwork Interfaces 28Wired
- Page 5 and 6: ContentsNavigating to an Access Poi
- Page 7: PrefaceTable 1 describes the typogr
- Page 11 and 12: Getting StartedConnecting the Acces
- Page 13 and 14: Getting StartedConnecting the Acces
- Page 15 and 16: Getting StartedConnecting the Acces
- Page 17 and 18: Getting StartedConnecting the Acces
- Page 19 and 20: Getting StartedConnecting the Acces
- Page 21 and 22: Getting StartedTroubleshooting Your
- Page 23 and 24: Getting StartedConfiguring the Acce
- Page 25 and 26: Getting StartedWireless Client Requ
- Page 27 and 28: Getting StartedConfiguring Security
- Page 29 and 30: 2StatusThe Status page provides inf
- Page 31 and 32: 2Table 3FieldDevice Information Pag
- Page 33 and 34: StatusTraffic Statistics2Figure 7Vi
- Page 35 and 36: StatusAssociated Clients2Associated
- Page 37 and 38: StatusRogue AP Detection2Link Integ
- Page 39 and 40: StatusRogue AP Detection2Table 6Fie
- Page 41 and 42: StatusRogue AP Detection2Table 6Fie
- Page 43 and 44: 3SetupLAN SettingsThe default wired
- Page 45 and 46: 3Table 7 describes the fields to vi
- Page 47 and 48: SetupConfiguring 802.1X Authenticat
- Page 49 and 50: SetupEnabling the Network Time Prot
- Page 51 and 52: SetupEnabling the Network Time Prot
- Page 53 and 54: SetupEnabling the Network Time Prot
- Page 55 and 56: 4WirelessModifying Wireless Radio S
- Page 57 and 58: 4Table 10FieldModeRadio Settings Fi
PrefaceOnline Help, Supported Browsers, and LimitationsOnline help for the <strong>Access</strong> <strong>Point</strong> Configuration Utility pages provides informationabout all fields and features available from the <strong>Access</strong> <strong>Point</strong> Configuration Utility.The information in the online help is a subset of the information available in the<strong>AP541N</strong> <strong>Dual</strong>-<strong>band</strong> <strong>Single</strong>-<strong>radio</strong> <strong>Access</strong> <strong>Point</strong> <strong>Administration</strong> Guide.Online help information corresponds to each page on the <strong>Access</strong> <strong>Point</strong>Configuration Utility.For information about the settings on the current page, click the Help link on theright side of a page.<strong>AP541N</strong> <strong>Dual</strong>-<strong>band</strong> <strong>Single</strong>-<strong>radio</strong> <strong>Access</strong> <strong>Point</strong> <strong>Administration</strong> Guide 5
Change language