Cisco AP541N Dual-band Single-radio Access Point Administration ...

More documents

Recommendations

Info

2StatusTraffic StatisticsTable 4FieldTraffic Statistics DescriptionDescriptionNetwork InterfacesStatusMAC AddressVLAN IDName (SSID)The name of the Ethernet or VAP interfaces.Shows whether the interface is up or down.MAC address for the specified interface. Each VAPinterface has a unique MAC address.A virtual LAN (VLAN) ID is used to establish multiplenetworks on the same access point. The VLAN ID isconfigured on the Wireless > VAP tab. (See BandwidthUtilization, page 96.)The network name, also known as the SSID, is analphanumeric key that uniquely identifies a VAP. Thename (SSID) is configured on the VAP tab. (SeeBandwidth Utilization, page 96.) NA means either thatthe entry is not applicable or is not supported.Transmit and Receive InformationTotal PacketsTotal BytesTotal Dropped PacketsTotal Dropped BytesErrorsIndicates total packets sent (in Transmit table) orreceived (in Received table) on that interface.Indicates total bytes sent (in Transmit table) orreceived (in Received table) on that interface.Indicates total number of packets sent (in Transmittable) or received (in Received table) on that interfacethat were dropped. NA means that the drop and errorcounters for the VAP interfaces and the WDSinterfaces are not supported.Indicates total number of bytes sent (in Transmit table)or received (in Received table) on that interface thatwere dropped. NA means that the drop and errorcounters for the VAP interfaces and the WDSinterfaces are not supported.Displays the total number of transmit and receiveerrors detected by the AP. NA means that the drop anderror counters for the VAP interfaces and the WDSinterfaces are not supported.31 Cisco AP 541N Dual-band Single-radio Access Point Quick Start Guide
StatusAssociated Clients2Associated ClientsTo view the client stations associated with the access point, click the AssociatedClients tab.Figure 8Viewing Client Association InformationThe associated stations are displayed along with information about packet traffictransmitted and received for each station. Click Refresh to refresh the page.Table 5 describes the fields on the Associated Clients page.Table 5FieldNetworkStationAssociated Clients Field DescriptionsDescriptionShows which VAP the client is associated with. Forexample, an entry of wlan0vap2 means the client isassociated with Wireless Radio 1, VAP 2.Shows the MAC address of the associated wirelessclient.Cisco AP 541N Dual-band Single-radio Access Point Quick Start Guide 32
Page 1 and 2: ADMINISTRATIONGUIDECisco Small Busi
Page 3 and 4: ContentsNetwork Interfaces 28Wired
Page 5 and 6: ContentsNavigating to an Access Poi
Page 7 and 8: PrefaceTable 1 describes the typogr
Page 9 and 10: 1Getting StartedThe Cisco Access Po
Page 11 and 12: Getting StartedConnecting the Acces
Page 21 and 22: Getting StartedTroubleshooting Your
Page 23 and 24: Getting StartedConfiguring the Acce
Page 25 and 26: Getting StartedWireless Client Requ
Page 27 and 28: Getting StartedConfiguring Security
Page 29 and 30: 2StatusThe Status page provides inf
Page 31 and 32: 2Table 3FieldDevice Information Pag
Page 33: StatusTraffic Statistics2Figure 7Vi
Page 37 and 38: StatusRogue AP Detection2Link Integ
Page 39 and 40: StatusRogue AP Detection2Table 6Fie
Page 41 and 42: StatusRogue AP Detection2Table 6Fie
Page 43 and 44: 3SetupLAN SettingsThe default wired
Page 45 and 46: 3Table 7 describes the fields to vi
Page 47 and 48: SetupConfiguring 802.1X Authenticat
Page 49 and 50: SetupEnabling the Network Time Prot
Page 55 and 56: 4WirelessModifying Wireless Radio S
Page 57 and 58: 4Table 10FieldModeRadio Settings Fi
Page 59 and 60: WirelessModifying Virtual Access Po
Page 79 and 80: WirelessClient Connection Control4C
Page 81 and 82: WirelessClient Connection Control4T
Page 83 and 84: WirelessModifying Advanced Settings
Page 85 and 86:
WirelessModifying Advanced Settings
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
WirelessConfiguring the Wireless Di
Page 97 and 98:
WirelessConfiguring the Wireless Di
Page 99 and 100:
WirelessBandwidth Utilization4Bandw
Page 101 and 102:
WirelessConfiguring Quality of Serv
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
5SNMPConfiguring SNMP on the Access
Page 109 and 110:
5Table 25FieldSNMP Settings (Contin
Page 111 and 112:
SNMPConfiguring SNMP on the Access
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
SNMPSNMP Targets5NOTEAfter you conf
Page 121 and 122:
6AdministrationAdministratorUse thi
Page 123 and 124:
6Access Point ConfigurationThe acce
Page 125 and 126:
AdministrationAccess Point Configur
Page 127 and 128:
AdministrationSoftware Upgrade6The
Page 129 and 130:
AdministrationSoftware Upgrade6The
Page 131 and 132:
AdministrationEvent Logs6Click Refr
Page 133 and 134:
AdministrationEvent Logs6Configurin
Page 135 and 136:
AdministrationConfiguring the Web S
Page 137 and 138:
AdministrationCreating an Administr
Page 139 and 140:
7Clustering Multiple Access PointsT
Page 141 and 142:
7Figure 33Cluster Information and M
Page 143 and 144:
Clustering Multiple Access PointsMa
Page 145 and 146:
Page 147 and 148:
Page 149 and 150:
Clustering Multiple Access PointsCo
Page 151 and 152:
Clustering Multiple Access PointsCo
Page 153 and 154:
Clustering Multiple Access PointsVi
Page 155 and 156:
Page 157 and 158:
Page 159 and 160:
8Configuration ExamplesThis chapter
Page 161 and 162:
8VAP Configuration from the Web Int
Page 163 and 164:
Configuration ExamplesConfiguring W
Page 165 and 166:
Configuration ExamplesConfiguring t
Page 167 and 168:
Configuration ExamplesConfiguring t
Page 169 and 170:
Configuration ExamplesClustering Ac
Page 171 and 172:
ADefault SettingsWhen you first pow
Page 173 and 174:
Default SettingsATable 43UAP Defaul
Page 175 and 176:
BWhere to Go From HereCisco provide
show all

Cisco AP541N Dual-band Single-radio Access Point Administration ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?