Cisco AP541N Dual-band Single-radio Access Point Administration ...
Cisco AP541N Dual-band Single-radio Access Point Administration ... Cisco AP541N Dual-band Single-radio Access Point Administration ...
1Getting StartedConfiguring Security on the Wireless Access Point• Station Isolation: Disabled• HTTP Redirect: DisableVAP2 has the following default settings:• VLAN ID: 1• SSID: cisco-scan• Broadcast SSID: Enabled• Security: WPA Personal• WPA Versions: WPA2• Cipher Suites: CCMP (AES)• Key: intermec• MAC Authentication Type: Disabled• Station Isolation: Disabled• HTTP Redirect: DisableVAP3-15 are disabeld by default, but when they are enabled they will have thefollowing default settings:• VLAN ID: 1• SSID: Virtual Access Point x ( where x is the VAP ID)• Broadcast SSID: Enabled• Security: None• MAC Authentication Type: Disabled• Station Isolation: Disabled• HTTP Redirect: DisableTo prevent unauthorized access to the access point, we recommend that youselect and configure a security option other than None for the default VAP and foreach VAP that you enable.For information about how to configure the security settings on each VAP, seeConfiguring the Wireless Distribution System, page 91.25 Cisco AP 541N Dual-band Single-radio Access Point Quick Start Guide
2StatusThe Status page provides information on the following:• Device Information• Network Interfaces• Traffic Statistics• Associated Clients• Rogue AP DetectionCisco AP 541N Dual-band Single-radio Access Point Quick Start Guide 26
- Page 1 and 2: ADMINISTRATIONGUIDECisco Small Busi
- Page 3 and 4: ContentsNetwork Interfaces 28Wired
- Page 5 and 6: ContentsNavigating to an Access Poi
- Page 7 and 8: PrefaceTable 1 describes the typogr
- Page 9 and 10: 1Getting StartedThe Cisco Access Po
- Page 11 and 12: Getting StartedConnecting the Acces
- Page 13 and 14: Getting StartedConnecting the Acces
- Page 15 and 16: Getting StartedConnecting the Acces
- Page 17 and 18: Getting StartedConnecting the Acces
- Page 19 and 20: Getting StartedConnecting the Acces
- Page 21 and 22: Getting StartedTroubleshooting Your
- Page 23 and 24: Getting StartedConfiguring the Acce
- Page 25 and 26: Getting StartedWireless Client Requ
- Page 27: Getting StartedConfiguring Security
- Page 31 and 32: 2Table 3FieldDevice Information Pag
- Page 33 and 34: StatusTraffic Statistics2Figure 7Vi
- Page 35 and 36: StatusAssociated Clients2Associated
- Page 37 and 38: StatusRogue AP Detection2Link Integ
- Page 39 and 40: StatusRogue AP Detection2Table 6Fie
- Page 41 and 42: StatusRogue AP Detection2Table 6Fie
- Page 43 and 44: 3SetupLAN SettingsThe default wired
- Page 45 and 46: 3Table 7 describes the fields to vi
- Page 47 and 48: SetupConfiguring 802.1X Authenticat
- Page 49 and 50: SetupEnabling the Network Time Prot
- Page 51 and 52: SetupEnabling the Network Time Prot
- Page 53 and 54: SetupEnabling the Network Time Prot
- Page 55 and 56: 4WirelessModifying Wireless Radio S
- Page 57 and 58: 4Table 10FieldModeRadio Settings Fi
- Page 59 and 60: WirelessModifying Virtual Access Po
- Page 61 and 62: WirelessModifying Virtual Access Po
- Page 63 and 64: WirelessModifying Virtual Access Po
- Page 65 and 66: WirelessModifying Virtual Access Po
- Page 67 and 68: WirelessModifying Virtual Access Po
- Page 69 and 70: WirelessModifying Virtual Access Po
- Page 71 and 72: WirelessModifying Virtual Access Po
- Page 73 and 74: WirelessModifying Virtual Access Po
- Page 75 and 76: WirelessModifying Virtual Access Po
- Page 77 and 78: WirelessModifying Virtual Access Po
1Getting StartedConfiguring Security on the Wireless <strong>Access</strong> <strong>Point</strong>• Station Isolation: Disabled• HTTP Redirect: DisableVAP2 has the following default settings:• VLAN ID: 1• SSID: cisco-scan• Broadcast SSID: Enabled• Security: WPA Personal• WPA Versions: WPA2• Cipher Suites: CCMP (AES)• Key: intermec• MAC Authentication Type: Disabled• Station Isolation: Disabled• HTTP Redirect: DisableVAP3-15 are disabeld by default, but when they are enabled they will have thefollowing default settings:• VLAN ID: 1• SSID: Virtual <strong>Access</strong> <strong>Point</strong> x ( where x is the VAP ID)• Broadcast SSID: Enabled• Security: None• MAC Authentication Type: Disabled• Station Isolation: Disabled• HTTP Redirect: DisableTo prevent unauthorized access to the access point, we recommend that youselect and configure a security option other than None for the default VAP and foreach VAP that you enable.For information about how to configure the security settings on each VAP, seeConfiguring the Wireless Distribution System, page 91.25 <strong>Cisco</strong> AP 541N <strong>Dual</strong>-<strong>band</strong> <strong>Single</strong>-<strong>radio</strong> <strong>Access</strong> <strong>Point</strong> Quick Start Guide