Cisco AP541N Dual-band Single-radio Access Point Administration ...
Cisco AP541N Dual-band Single-radio Access Point Administration ... Cisco AP541N Dual-band Single-radio Access Point Administration ...
8Configuration ExamplesClustering Access PointsClustering Access Points by Using SNMPCluster configuration by using SNMP is not supported.167 Cisco AP 541N Dual-band Single-radio Access Point Quick Start Guide
ADefault SettingsWhen you first power on an access point, it has the default settings shown inTable 43.Table 43UAP Default SettingsFeatureSystem InformationUser NamePasswordEthernet Interface SettingsConnection TypeDHCPIP AddressDefaultciscociscoDHCPEnabledSubnet Mask 255.255.255.0DNS NameManagement VLAN ID 1Untagged VLAN ID 1Radio SettingsRadioRadio 1 IEEE 802.11 Mode802.11b/g/n ChannelWireless Radio 1 ChannelBandwidth802.11a/n Channel192.168.10.10 (if no DHCP server is connected)NoneOff802.11b/g/nAuto20 MHzAutoDefault Settings 168
- Page 119 and 120: SNMPSNMP Targets5NOTEAfter you conf
- Page 121 and 122: 6AdministrationAdministratorUse thi
- Page 123 and 124: 6Access Point ConfigurationThe acce
- Page 125 and 126: AdministrationAccess Point Configur
- Page 127 and 128: AdministrationSoftware Upgrade6The
- Page 129 and 130: AdministrationSoftware Upgrade6The
- Page 131 and 132: AdministrationEvent Logs6Click Refr
- Page 133 and 134: AdministrationEvent Logs6Configurin
- Page 135 and 136: AdministrationConfiguring the Web S
- Page 137 and 138: AdministrationCreating an Administr
- Page 139 and 140: 7Clustering Multiple Access PointsT
- Page 141 and 142: 7Figure 33Cluster Information and M
- Page 143 and 144: Clustering Multiple Access PointsMa
- Page 145 and 146: Clustering Multiple Access PointsMa
- Page 147 and 148: Clustering Multiple Access PointsMa
- Page 149 and 150: Clustering Multiple Access PointsCo
- Page 151 and 152: Clustering Multiple Access PointsCo
- Page 153 and 154: Clustering Multiple Access PointsVi
- Page 155 and 156: Clustering Multiple Access PointsVi
- Page 157 and 158: Clustering Multiple Access PointsVi
- Page 159 and 160: 8Configuration ExamplesThis chapter
- Page 161 and 162: 8VAP Configuration from the Web Int
- Page 163 and 164: Configuration ExamplesConfiguring W
- Page 165 and 166: Configuration ExamplesConfiguring t
- Page 167 and 168: Configuration ExamplesConfiguring t
- Page 169: Configuration ExamplesClustering Ac
- Page 173 and 174: Default SettingsATable 43UAP Defaul
- Page 175 and 176: BWhere to Go From HereCisco provide
ADefault SettingsWhen you first power on an access point, it has the default settings shown inTable 43.Table 43UAP Default SettingsFeatureSystem InformationUser NamePasswordEthernet Interface SettingsConnection TypeDHCPIP AddressDefaultciscociscoDHCPEnabledSubnet Mask 255.255.255.0DNS NameManagement VLAN ID 1Untagged VLAN ID 1Radio SettingsRadioRadio 1 IEEE 802.11 Mode802.11b/g/n ChannelWireless Radio 1 ChannelBandwidth802.11a/n Channel192.168.10.10 (if no DHCP server is connected)NoneOff802.11b/g/nAuto20 MHzAutoDefault Settings 168