Cisco AP541N Dual-band Single-radio Access Point Administration ...

More documents

Recommendations

Info

1Getting StartedConnecting the Access Point to a PCFigure 4Getting Started PageSTEP 3Update the Cisco AP 541N software with the latest version by clicking the SoftwareUpgrade link, as shown in Figure 4.Next, we recommend that you:• Change the password by clicking Change Administrator Password.• Configure the SSID and enable wireless security, by clicking ConfigureWireless Networks (SSIDs).• Enable the wireless radio, by clicking Enable Wireless Radio.• Assign a new static IP address to the access point if your network devicesare configured with static IP addresses, by clicking Set LAN IP Address.13 Cisco AP 541N Dual-band Single-radio Access Point Quick Start Guide
Getting StartedConnecting the Access Point to a PC1Display the Configuration Utility by UsingCisco Configuration Assistant 2.1 or higherUse Cisco Configuration Assistant 2.1 or higher (CCA) to configure the accesspoint when it is deployed in a Cisco Smart Business Communications System(SBCS) network with a UC520 or SR520.DHCP clientInternet195058This procedure assumes you are familiar with CCA. You can find additionalinformation about CCA at http://www.cisco.com/en/US/products/ps7287/tsd_products_support_series_home.htmlTo configure the access point by using CCA:STEP 1STEP 2STEP 3STEP 4STEP 5STEP 6Connect the Ethernet port on the access point to a switch port on a SBCS device.Power on the Cisco AP541N.Connect a PC with CCA installed to any access switch port on the UC520 orSR520.Create a new CCA site by entering a name and the IP address of the UC520 orSR520.Connect to the CCA site by using the appropriate login credentials.Click Window > Topology View.Cisco AP 541N Dual-band Single-radio Access Point Quick Start Guide 14
Page 1 and 2: ADMINISTRATIONGUIDECisco Small Busi
Page 3 and 4: ContentsNetwork Interfaces 28Wired
Page 5 and 6: ContentsNavigating to an Access Poi
Page 7 and 8: PrefaceTable 1 describes the typogr
Page 9 and 10: 1Getting StartedThe Cisco Access Po
Page 11 and 12: Getting StartedConnecting the Acces
Page 15: Getting StartedConnecting the Acces
Page 21 and 22: Getting StartedTroubleshooting Your
Page 23 and 24: Getting StartedConfiguring the Acce
Page 25 and 26: Getting StartedWireless Client Requ
Page 27 and 28: Getting StartedConfiguring Security
Page 29 and 30: 2StatusThe Status page provides inf
Page 31 and 32: 2Table 3FieldDevice Information Pag
Page 33 and 34: StatusTraffic Statistics2Figure 7Vi
Page 35 and 36: StatusAssociated Clients2Associated
Page 37 and 38: StatusRogue AP Detection2Link Integ
Page 39 and 40: StatusRogue AP Detection2Table 6Fie
Page 41 and 42: StatusRogue AP Detection2Table 6Fie
Page 43 and 44: 3SetupLAN SettingsThe default wired
Page 45 and 46: 3Table 7 describes the fields to vi
Page 47 and 48: SetupConfiguring 802.1X Authenticat
Page 49 and 50: SetupEnabling the Network Time Prot
Page 55 and 56: 4WirelessModifying Wireless Radio S
Page 57 and 58: 4Table 10FieldModeRadio Settings Fi
Page 59 and 60: WirelessModifying Virtual Access Po
Page 67 and 68:
WirelessModifying Virtual Access Po
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
WirelessClient Connection Control4C
Page 81 and 82:
WirelessClient Connection Control4T
Page 83 and 84:
WirelessModifying Advanced Settings
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
WirelessConfiguring the Wireless Di
Page 97 and 98:
WirelessConfiguring the Wireless Di
Page 99 and 100:
WirelessBandwidth Utilization4Bandw
Page 101 and 102:
WirelessConfiguring Quality of Serv
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
5SNMPConfiguring SNMP on the Access
Page 109 and 110:
5Table 25FieldSNMP Settings (Contin
Page 111 and 112:
SNMPConfiguring SNMP on the Access
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
SNMPSNMP Targets5NOTEAfter you conf
Page 121 and 122:
6AdministrationAdministratorUse thi
Page 123 and 124:
6Access Point ConfigurationThe acce
Page 125 and 126:
AdministrationAccess Point Configur
Page 127 and 128:
AdministrationSoftware Upgrade6The
Page 129 and 130:
AdministrationSoftware Upgrade6The
Page 131 and 132:
AdministrationEvent Logs6Click Refr
Page 133 and 134:
AdministrationEvent Logs6Configurin
Page 135 and 136:
AdministrationConfiguring the Web S
Page 137 and 138:
AdministrationCreating an Administr
Page 139 and 140:
7Clustering Multiple Access PointsT
Page 141 and 142:
7Figure 33Cluster Information and M
Page 143 and 144:
Clustering Multiple Access PointsMa
Page 145 and 146:
Page 147 and 148:
Page 149 and 150:
Clustering Multiple Access PointsCo
Page 151 and 152:
Clustering Multiple Access PointsCo
Page 153 and 154:
Clustering Multiple Access PointsVi
Page 155 and 156:
Page 157 and 158:
Page 159 and 160:
8Configuration ExamplesThis chapter
Page 161 and 162:
8VAP Configuration from the Web Int
Page 163 and 164:
Configuration ExamplesConfiguring W
Page 165 and 166:
Configuration ExamplesConfiguring t
Page 167 and 168:
Configuration ExamplesConfiguring t
Page 169 and 170:
Configuration ExamplesClustering Ac
Page 171 and 172:
ADefault SettingsWhen you first pow
Page 173 and 174:
Default SettingsATable 43UAP Defaul
Page 175 and 176:
BWhere to Go From HereCisco provide
show all

Cisco AP541N Dual-band Single-radio Access Point Administration ...

Create successful ePaper yourself

Delete template?

Save as template?