Cisco AP541N Dual-band Single-radio Access Point Administration ...
Cisco AP541N Dual-band Single-radio Access Point Administration ... Cisco AP541N Dual-band Single-radio Access Point Administration ...
7Clustering Multiple Access PointsConfiguring and Viewing Channel Management Settings• Click Start to resume automatic channel assignment.When automatic channel assignment is enabled, the Channel Managerperiodically maps radio channels used by clustered access points and, ifnecessary, re-assigns channels on clustered access points to reduceinterference with cluster members or other access points outside thecluster.• Click Stop to stop automatic channel assignment. (No channel usage mapsor channel re-assignments will be made. Only manual updates will affectthe channel assignment.)NOTEThe proposed channel assignment will not take effect if the Channel field on theWireless Radio page is set to auto. The channel must be set to a static channel.Viewing Current Channel Assignments and Setting LocksThe Current Channel Assignments section shows a list of all access points in thecluster by IP Address. The display shows the band on which each access point isbroadcasting (a/b/g/n), the current channel used by each access point, and anoption to lock an access point on its current radio channel so that it cannot be reassignedto another.Table 38 provides details about Current Channel Assignments.Table 38Channel AssignmentsFieldIP AddressWireless RadioBandChannelDescriptionIP Address for the access point.MAC address of the radio.Band on which the access point is broadcasting.Radio channel on which this access point is currentlybroadcasting.147 Cisco AP 541N Dual-band Single-radio Access Point Quick Start Guide
Clustering Multiple Access PointsConfiguring and Viewing Channel Management Settings7Table 38FieldLockedChannel AssignmentsDescriptionClick Locked to force the access point to remain onthe current channel.When Locked is selected (enabled) for an accesspoint, automated channel management plans do notre-assign the access point to a different channel as apart of the optimization strategy. Instead, accesspoints with locked channels are factored in asrequirements for the plan.If you click Apply, you will see that locked accesspoints show the same channel for the CurrentChannel and Proposed Channel fields. The lockedaccess points keep their current channels.Viewing the Last Proposed Set of ChangesThe Proposed Channel Assignments shows the last channel plan. The planlists all access points in the cluster by IP Address, and shows the current andproposed channels for each access point. Locked channels will not be reassignedand the optimization of channel distribution among access points willtake into account the fact that locked access points must remain on their currentchannels. access points that are not locked may be assigned to different channelsthan they were previously using, depending on the results of the plan.Table 39Last Proposed ChangesFieldIP AddressWireless RadioProposed ChannelDescriptionIP address for the access point.Radio channel on which this access point is currentlybroadcasting.Radio channel to which this access point would bere-assigned if the Channel Plan is executed.Cisco AP 541N Dual-band Single-radio Access Point Quick Start Guide 148
- Page 99 and 100: WirelessBandwidth Utilization4Bandw
- Page 101 and 102: WirelessConfiguring Quality of Serv
- Page 103 and 104: WirelessConfiguring Quality of Serv
- Page 105 and 106: WirelessConfiguring Quality of Serv
- Page 107 and 108: 5SNMPConfiguring SNMP on the Access
- Page 109 and 110: 5Table 25FieldSNMP Settings (Contin
- Page 111 and 112: SNMPConfiguring SNMP on the Access
- Page 113 and 114: SNMPConfiguring SNMP on the Access
- Page 115 and 116: SNMPConfiguring SNMP on the Access
- Page 117 and 118: SNMPConfiguring SNMP on the Access
- Page 119 and 120: SNMPSNMP Targets5NOTEAfter you conf
- Page 121 and 122: 6AdministrationAdministratorUse thi
- Page 123 and 124: 6Access Point ConfigurationThe acce
- Page 125 and 126: AdministrationAccess Point Configur
- Page 127 and 128: AdministrationSoftware Upgrade6The
- Page 129 and 130: AdministrationSoftware Upgrade6The
- Page 131 and 132: AdministrationEvent Logs6Click Refr
- Page 133 and 134: AdministrationEvent Logs6Configurin
- Page 135 and 136: AdministrationConfiguring the Web S
- Page 137 and 138: AdministrationCreating an Administr
- Page 139 and 140: 7Clustering Multiple Access PointsT
- Page 141 and 142: 7Figure 33Cluster Information and M
- Page 143 and 144: Clustering Multiple Access PointsMa
- Page 145 and 146: Clustering Multiple Access PointsMa
- Page 147 and 148: Clustering Multiple Access PointsMa
- Page 149: Clustering Multiple Access PointsCo
- Page 153 and 154: Clustering Multiple Access PointsVi
- Page 155 and 156: Clustering Multiple Access PointsVi
- Page 157 and 158: Clustering Multiple Access PointsVi
- Page 159 and 160: 8Configuration ExamplesThis chapter
- Page 161 and 162: 8VAP Configuration from the Web Int
- Page 163 and 164: Configuration ExamplesConfiguring W
- Page 165 and 166: Configuration ExamplesConfiguring t
- Page 167 and 168: Configuration ExamplesConfiguring t
- Page 169 and 170: Configuration ExamplesClustering Ac
- Page 171 and 172: ADefault SettingsWhen you first pow
- Page 173 and 174: Default SettingsATable 43UAP Defaul
- Page 175 and 176: BWhere to Go From HereCisco provide
7Clustering Multiple <strong>Access</strong> <strong>Point</strong>sConfiguring and Viewing Channel Management Settings• Click Start to resume automatic channel assignment.When automatic channel assignment is enabled, the Channel Managerperiodically maps <strong>radio</strong> channels used by clustered access points and, ifnecessary, re-assigns channels on clustered access points to reduceinterference with cluster members or other access points outside thecluster.• Click Stop to stop automatic channel assignment. (No channel usage mapsor channel re-assignments will be made. Only manual updates will affectthe channel assignment.)NOTEThe proposed channel assignment will not take effect if the Channel field on theWireless Radio page is set to auto. The channel must be set to a static channel.Viewing Current Channel Assignments and Setting LocksThe Current Channel Assignments section shows a list of all access points in thecluster by IP Address. The display shows the <strong>band</strong> on which each access point isbroadcasting (a/b/g/n), the current channel used by each access point, and anoption to lock an access point on its current <strong>radio</strong> channel so that it cannot be reassignedto another.Table 38 provides details about Current Channel Assignments.Table 38Channel AssignmentsFieldIP AddressWireless RadioBandChannelDescriptionIP Address for the access point.MAC address of the <strong>radio</strong>.Band on which the access point is broadcasting.Radio channel on which this access point is currentlybroadcasting.147 <strong>Cisco</strong> AP 541N <strong>Dual</strong>-<strong>band</strong> <strong>Single</strong>-<strong>radio</strong> <strong>Access</strong> <strong>Point</strong> Quick Start Guide
Change language