Cisco AP541N Dual-band Single-radio Access Point Administration ...

More documents

Recommendations

Info

6AdministrationCreating an Administration Access Control ListTable 34Management ACLFieldManagement ACLModeIP Address (1–5)DescriptionEnable or disable the management ACL feature. At leastone IPv4 address should be configured before enablingManagement ACL Mode. If enabled, only the IPaddresses you specify will have Web, Telnet, SSH andSNMP access to the management interface.Enter up to five IPv4 addresses that are allowedmanagement access to the access point. Use dotteddecimalformat (for example, 192.168.10.100).135 Cisco AP 541N Dual-band Single-radio Access Point Quick Start Guide
7Clustering Multiple Access PointsThe Cisco AP 541N supports access point clusters. A cluster provides a singlepoint of administration and lets you view, deploy, configure, and secure thewireless network as a single entity rather than a series of separate wirelessdevices.Managing Access Points in the ClusterThe access point cluster is a dynamic, configuration-aware group of access pointsin the same subnet of a network. Each cluster can have up to 10 members. Thecluster provides a single point of administration and enables you to view thedeployment of access points as a single wireless network rather than a series ofseparate wireless devices. A network subnet can have multiple clusters. Clusterscan share various configuration information, such as VAP settings and QoS queueparameters.A cluster can be formed between two access points if the following conditions aremet:• The access points use the same radio mode. (For example, both radios use802.11g.)• The access points are connected on the same bridged segment.• The access points joining the cluster have the same Cluster Name.• Clustering mode is enabled on both access points.NOTEFor two access points to be in the same cluster, they do not need to have the samenumber of radios; however, the supported capabilities of the radios should besame.Cisco AP 541N Dual-band Single-radio Access Point Quick Start Guide 136
Page 1 and 2:
ADMINISTRATIONGUIDECisco Small Busi
Page 3 and 4:
ContentsNetwork Interfaces 28Wired
Page 5 and 6:
ContentsNavigating to an Access Poi
Page 7 and 8:
PrefaceTable 1 describes the typogr
Page 9 and 10:
1Getting StartedThe Cisco Access Po
Page 11 and 12:
Getting StartedConnecting the Acces
Page 13 and 14:
Page 15 and 16:
Page 17 and 18:
Page 19 and 20:
Page 21 and 22:
Getting StartedTroubleshooting Your
Page 23 and 24:
Getting StartedConfiguring the Acce
Page 25 and 26:
Getting StartedWireless Client Requ
Page 27 and 28:
Getting StartedConfiguring Security
Page 29 and 30:
2StatusThe Status page provides inf
Page 31 and 32:
2Table 3FieldDevice Information Pag
Page 33 and 34:
StatusTraffic Statistics2Figure 7Vi
Page 35 and 36:
StatusAssociated Clients2Associated
Page 37 and 38:
StatusRogue AP Detection2Link Integ
Page 39 and 40:
StatusRogue AP Detection2Table 6Fie
Page 41 and 42:
StatusRogue AP Detection2Table 6Fie
Page 43 and 44:
3SetupLAN SettingsThe default wired
Page 45 and 46:
3Table 7 describes the fields to vi
Page 47 and 48:
SetupConfiguring 802.1X Authenticat
Page 49 and 50:
SetupEnabling the Network Time Prot
Page 51 and 52:
Page 53 and 54:
Page 55 and 56:
4WirelessModifying Wireless Radio S
Page 57 and 58:
4Table 10FieldModeRadio Settings Fi
Page 59 and 60:
WirelessModifying Virtual Access Po
Page 61 and 62:
Page 63 and 64:
Page 65 and 66:
Page 67 and 68:
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
WirelessClient Connection Control4C
Page 81 and 82:
WirelessClient Connection Control4T
Page 83 and 84:
WirelessModifying Advanced Settings
Page 85 and 86:
WirelessModifying Advanced Settings
Page 87 and 88: WirelessModifying Advanced Settings
Page 95 and 96: WirelessConfiguring the Wireless Di
Page 97 and 98: WirelessConfiguring the Wireless Di
Page 99 and 100: WirelessBandwidth Utilization4Bandw
Page 101 and 102: WirelessConfiguring Quality of Serv
Page 107 and 108: 5SNMPConfiguring SNMP on the Access
Page 109 and 110: 5Table 25FieldSNMP Settings (Contin
Page 111 and 112: SNMPConfiguring SNMP on the Access
Page 119 and 120: SNMPSNMP Targets5NOTEAfter you conf
Page 121 and 122: 6AdministrationAdministratorUse thi
Page 123 and 124: 6Access Point ConfigurationThe acce
Page 125 and 126: AdministrationAccess Point Configur
Page 127 and 128: AdministrationSoftware Upgrade6The
Page 129 and 130: AdministrationSoftware Upgrade6The
Page 131 and 132: AdministrationEvent Logs6Click Refr
Page 133 and 134: AdministrationEvent Logs6Configurin
Page 135 and 136: AdministrationConfiguring the Web S
Page 137: AdministrationCreating an Administr
Page 141 and 142: 7Figure 33Cluster Information and M
Page 143 and 144: Clustering Multiple Access PointsMa
Page 149 and 150: Clustering Multiple Access PointsCo
Page 151 and 152: Clustering Multiple Access PointsCo
Page 153 and 154: Clustering Multiple Access PointsVi
Page 159 and 160: 8Configuration ExamplesThis chapter
Page 161 and 162: 8VAP Configuration from the Web Int
Page 163 and 164: Configuration ExamplesConfiguring W
Page 165 and 166: Configuration ExamplesConfiguring t
Page 167 and 168: Configuration ExamplesConfiguring t
Page 169 and 170: Configuration ExamplesClustering Ac
Page 171 and 172: ADefault SettingsWhen you first pow
Page 173 and 174: Default SettingsATable 43UAP Defaul
Page 175 and 176: BWhere to Go From HereCisco provide
show all

Cisco AP541N Dual-band Single-radio Access Point Administration ...

Create successful ePaper yourself

Delete template?

Save as template?