Cisco AP541N Dual-band Single-radio Access Point Administration ...

More documents

Recommendations

Info

6AdministrationAccess Point ConfigurationSTEP 4Click the Restore button.The access point reboots. A reboot confirmation dialog and follow-on rebootingstatus message displays. Please wait for the reboot process to complete, whichmight take several minutes.The Configuration Utility is not accessible until the access point has rebooted.Restoring the Current Configuration by Using HTTPUse the following steps to save a copy of the current settings on an access pointto a backup configuration file by using HTTP:STEP 1Clear the Use TFTP to upload the file option.When you clear the radio button, the Server IP field is disabled.STEP 2STEP 3Enter the name of the file to restore.Click Restore.A File Upload or Choose File dialog box displays.STEP 4Navigate to the directory that contains the file, then select the file to upload andclick Open.NOTE Only those files saved as .xml backup configuration files are valid to use withRestore; for example, ap_config.xml.STEP 5Click Restore.123 Cisco AP 541N Dual-band Single-radio Access Point Quick Start Guide
AdministrationSoftware Upgrade6The access point reboots. A reboot confirmation dialog and follow-on rebootingstatus message displays. Please wait for the reboot process to complete, whichmight take several minutes.The Configuration Utility is not accessible until the access point has rebooted.Rebooting the Access PointFor maintenance purposes or as a troubleshooting measure, you can reboot theaccess point. To reboot the access point, click the Reboot button on theConfiguration page.Software UpgradeAs new versions of the access point software become available, you can upgradethe software on your devices to take advantage of new features andenhancements. The access point uses a TFTP client for software upgrades. Youcan also use HTTP to perform software upgrades.NOTEWhen you upgrade the software, the access point retains the existing configurationinformation.NOTEBy default, the access point uses HTTP for software upgrades instead of TFTP.Upgrading the Software by using TFTPUse the following steps to upgrade the software on an access point by usingTFTP:STEP 1Click the Software Upgrade tab in the Administration section.Information about the current software version is displayed and an option toupgrade a new software image is provided.Cisco AP 541N Dual-band Single-radio Access Point Quick Start Guide 124
Page 1 and 2:
ADMINISTRATIONGUIDECisco Small Busi
Page 3 and 4:
ContentsNetwork Interfaces 28Wired
Page 5 and 6:
ContentsNavigating to an Access Poi
Page 7 and 8:
PrefaceTable 1 describes the typogr
Page 9 and 10:
1Getting StartedThe Cisco Access Po
Page 11 and 12:
Getting StartedConnecting the Acces
Page 13 and 14:
Page 15 and 16:
Page 17 and 18:
Page 19 and 20:
Page 21 and 22:
Getting StartedTroubleshooting Your
Page 23 and 24:
Getting StartedConfiguring the Acce
Page 25 and 26:
Getting StartedWireless Client Requ
Page 27 and 28:
Getting StartedConfiguring Security
Page 29 and 30:
2StatusThe Status page provides inf
Page 31 and 32:
2Table 3FieldDevice Information Pag
Page 33 and 34:
StatusTraffic Statistics2Figure 7Vi
Page 35 and 36:
StatusAssociated Clients2Associated
Page 37 and 38:
StatusRogue AP Detection2Link Integ
Page 39 and 40:
StatusRogue AP Detection2Table 6Fie
Page 41 and 42:
StatusRogue AP Detection2Table 6Fie
Page 43 and 44:
3SetupLAN SettingsThe default wired
Page 45 and 46:
3Table 7 describes the fields to vi
Page 47 and 48:
SetupConfiguring 802.1X Authenticat
Page 49 and 50:
SetupEnabling the Network Time Prot
Page 51 and 52:
Page 53 and 54:
Page 55 and 56:
4WirelessModifying Wireless Radio S
Page 57 and 58:
4Table 10FieldModeRadio Settings Fi
Page 59 and 60:
WirelessModifying Virtual Access Po
Page 61 and 62:
Page 63 and 64:
Page 65 and 66:
Page 67 and 68:
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Page 75 and 76: WirelessModifying Virtual Access Po
Page 77 and 78: WirelessModifying Virtual Access Po
Page 79 and 80: WirelessClient Connection Control4C
Page 81 and 82: WirelessClient Connection Control4T
Page 83 and 84: WirelessModifying Advanced Settings
Page 95 and 96: WirelessConfiguring the Wireless Di
Page 97 and 98: WirelessConfiguring the Wireless Di
Page 99 and 100: WirelessBandwidth Utilization4Bandw
Page 101 and 102: WirelessConfiguring Quality of Serv
Page 107 and 108: 5SNMPConfiguring SNMP on the Access
Page 109 and 110: 5Table 25FieldSNMP Settings (Contin
Page 111 and 112: SNMPConfiguring SNMP on the Access
Page 119 and 120: SNMPSNMP Targets5NOTEAfter you conf
Page 121 and 122: 6AdministrationAdministratorUse thi
Page 123 and 124: 6Access Point ConfigurationThe acce
Page 125: AdministrationAccess Point Configur
Page 129 and 130: AdministrationSoftware Upgrade6The
Page 131 and 132: AdministrationEvent Logs6Click Refr
Page 133 and 134: AdministrationEvent Logs6Configurin
Page 135 and 136: AdministrationConfiguring the Web S
Page 137 and 138: AdministrationCreating an Administr
Page 139 and 140: 7Clustering Multiple Access PointsT
Page 141 and 142: 7Figure 33Cluster Information and M
Page 143 and 144: Clustering Multiple Access PointsMa
Page 149 and 150: Clustering Multiple Access PointsCo
Page 151 and 152: Clustering Multiple Access PointsCo
Page 153 and 154: Clustering Multiple Access PointsVi
Page 159 and 160: 8Configuration ExamplesThis chapter
Page 161 and 162: 8VAP Configuration from the Web Int
Page 163 and 164: Configuration ExamplesConfiguring W
Page 165 and 166: Configuration ExamplesConfiguring t
Page 167 and 168: Configuration ExamplesConfiguring t
Page 169 and 170: Configuration ExamplesClustering Ac
Page 171 and 172: ADefault SettingsWhen you first pow
Page 173 and 174: Default SettingsATable 43UAP Defaul
Page 175 and 176: BWhere to Go From HereCisco provide
show all

Cisco AP541N Dual-band Single-radio Access Point Administration ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?