Cisco AP541N Dual-band Single-radio Access Point Administration ...
Cisco AP541N Dual-band Single-radio Access Point Administration ... Cisco AP541N Dual-band Single-radio Access Point Administration ...
5SNMPSNMP TargetsSNMP TargetsSNMPv3 Targets send trap messages to the SNMP manager. Each target isidentified by a target name and associated with target IP address, UDP port, andSNMP user name.Figure 25SNMPv3 TargetTable 29SNMPv3 TargetsFieldIP AddressPortUsersSNMPv3TargetsDescriptionEnter the IP address of the remote SNMP manager to receivethe target.Enter the UDP port to use for sending SNMP targets.Enter the name of the SNMP user to associate with the target.Toconfigure SNMP users, see Configuring SNMP Users, page113.This field shows the SNMPv3 Targets on the access point. Toremove a target, select it and click Remove.115 Cisco AP 541N Dual-band Single-radio Access Point Quick Start Guide
SNMPSNMP Targets5NOTEAfter you configure the SNMPv3 Target settings, you must click Apply to apply thechanges and to save the settings.Cisco AP 541N Dual-band Single-radio Access Point Quick Start Guide 116
- Page 67 and 68: WirelessModifying Virtual Access Po
- Page 69 and 70: WirelessModifying Virtual Access Po
- Page 71 and 72: WirelessModifying Virtual Access Po
- Page 73 and 74: WirelessModifying Virtual Access Po
- Page 75 and 76: WirelessModifying Virtual Access Po
- Page 77 and 78: WirelessModifying Virtual Access Po
- Page 79 and 80: WirelessClient Connection Control4C
- Page 81 and 82: WirelessClient Connection Control4T
- Page 83 and 84: WirelessModifying Advanced Settings
- Page 85 and 86: WirelessModifying Advanced Settings
- Page 87 and 88: WirelessModifying Advanced Settings
- Page 89 and 90: WirelessModifying Advanced Settings
- Page 91 and 92: WirelessModifying Advanced Settings
- Page 93 and 94: WirelessModifying Advanced Settings
- Page 95 and 96: WirelessConfiguring the Wireless Di
- Page 97 and 98: WirelessConfiguring the Wireless Di
- Page 99 and 100: WirelessBandwidth Utilization4Bandw
- Page 101 and 102: WirelessConfiguring Quality of Serv
- Page 103 and 104: WirelessConfiguring Quality of Serv
- Page 105 and 106: WirelessConfiguring Quality of Serv
- Page 107 and 108: 5SNMPConfiguring SNMP on the Access
- Page 109 and 110: 5Table 25FieldSNMP Settings (Contin
- Page 111 and 112: SNMPConfiguring SNMP on the Access
- Page 113 and 114: SNMPConfiguring SNMP on the Access
- Page 115 and 116: SNMPConfiguring SNMP on the Access
- Page 117: SNMPConfiguring SNMP on the Access
- Page 121 and 122: 6AdministrationAdministratorUse thi
- Page 123 and 124: 6Access Point ConfigurationThe acce
- Page 125 and 126: AdministrationAccess Point Configur
- Page 127 and 128: AdministrationSoftware Upgrade6The
- Page 129 and 130: AdministrationSoftware Upgrade6The
- Page 131 and 132: AdministrationEvent Logs6Click Refr
- Page 133 and 134: AdministrationEvent Logs6Configurin
- Page 135 and 136: AdministrationConfiguring the Web S
- Page 137 and 138: AdministrationCreating an Administr
- Page 139 and 140: 7Clustering Multiple Access PointsT
- Page 141 and 142: 7Figure 33Cluster Information and M
- Page 143 and 144: Clustering Multiple Access PointsMa
- Page 145 and 146: Clustering Multiple Access PointsMa
- Page 147 and 148: Clustering Multiple Access PointsMa
- Page 149 and 150: Clustering Multiple Access PointsCo
- Page 151 and 152: Clustering Multiple Access PointsCo
- Page 153 and 154: Clustering Multiple Access PointsVi
- Page 155 and 156: Clustering Multiple Access PointsVi
- Page 157 and 158: Clustering Multiple Access PointsVi
- Page 159 and 160: 8Configuration ExamplesThis chapter
- Page 161 and 162: 8VAP Configuration from the Web Int
- Page 163 and 164: Configuration ExamplesConfiguring W
- Page 165 and 166: Configuration ExamplesConfiguring t
- Page 167 and 168: Configuration ExamplesConfiguring t
SNMPSNMP Targets5NOTEAfter you configure the SNMPv3 Target settings, you must click Apply to apply thechanges and to save the settings.<strong>Cisco</strong> AP 541N <strong>Dual</strong>-<strong>band</strong> <strong>Single</strong>-<strong>radio</strong> <strong>Access</strong> <strong>Point</strong> Quick Start Guide 116