Cisco AP541N Dual-band Single-radio Access Point Administration ...

More documents

Recommendations

Info

4WirelessConfiguring Quality of Service (QoS)103 Cisco AP 541N Dual-band Single-radio Access Point Quick Start Guide
5SNMPConfiguring SNMP on the Access PointSimple Network Management Protocol (SNMP) defines a standard for recording,storing, and sharing information about network devices. SNMP facilitates networkmanagement, troubleshooting, and maintenance. The access point supportsSNMP versions 1, 2, and 3. Unless specifically noted, all configuration parameterson this page apply to SNMPv1 and SNMPv2c only.Key components of any SNMP-managed network are managed devices, SNMPagents, and a management system. The agents store data about their devices inManagement Information Bases (MIBs) and return this data to the SNMP managerwhen requested. Managed devices can be network nodes such as access points,routers, switches, bridges, hubs, servers, or printers.The access point can function as an SNMP managed device for seamlessintegration into network management systems such as HP OpenView.From the SNMP page, you can start or stop control of SNMP agents, configurecommunity passwords, access MIBs, and configure SNMP Trap destinations.From the pages under the SNMP heading, you can manage SNMPv3 users andtheir security levels and define access control to the SNMP MIBs. For informationabout how to configure SNMPv3 views, groups, users, and targets, seeConfiguring SNMP Views, page 108.To configure SNMP, click the General tab under the SNMP heading and update thefields described in Table 25 on page 105.Cisco AP 541N Dual-band Single-radio Access Point Quick Start Guide 104
Page 1 and 2:
ADMINISTRATIONGUIDECisco Small Busi
Page 3 and 4:
ContentsNetwork Interfaces 28Wired
Page 5 and 6:
ContentsNavigating to an Access Poi
Page 7 and 8:
PrefaceTable 1 describes the typogr
Page 9 and 10:
1Getting StartedThe Cisco Access Po
Page 11 and 12:
Getting StartedConnecting the Acces
Page 13 and 14:
Page 15 and 16:
Page 17 and 18:
Page 19 and 20:
Page 21 and 22:
Getting StartedTroubleshooting Your
Page 23 and 24:
Getting StartedConfiguring the Acce
Page 25 and 26:
Getting StartedWireless Client Requ
Page 27 and 28:
Getting StartedConfiguring Security
Page 29 and 30:
2StatusThe Status page provides inf
Page 31 and 32:
2Table 3FieldDevice Information Pag
Page 33 and 34:
StatusTraffic Statistics2Figure 7Vi
Page 35 and 36:
StatusAssociated Clients2Associated
Page 37 and 38:
StatusRogue AP Detection2Link Integ
Page 39 and 40:
StatusRogue AP Detection2Table 6Fie
Page 41 and 42:
StatusRogue AP Detection2Table 6Fie
Page 43 and 44:
3SetupLAN SettingsThe default wired
Page 45 and 46:
3Table 7 describes the fields to vi
Page 47 and 48:
SetupConfiguring 802.1X Authenticat
Page 49 and 50:
SetupEnabling the Network Time Prot
Page 51 and 52:
Page 53 and 54:
Page 55 and 56: 4WirelessModifying Wireless Radio S
Page 57 and 58: 4Table 10FieldModeRadio Settings Fi
Page 59 and 60: WirelessModifying Virtual Access Po
Page 79 and 80: WirelessClient Connection Control4C
Page 81 and 82: WirelessClient Connection Control4T
Page 83 and 84: WirelessModifying Advanced Settings
Page 95 and 96: WirelessConfiguring the Wireless Di
Page 97 and 98: WirelessConfiguring the Wireless Di
Page 99 and 100: WirelessBandwidth Utilization4Bandw
Page 101 and 102: WirelessConfiguring Quality of Serv
Page 103 and 104: WirelessConfiguring Quality of Serv
Page 105: WirelessConfiguring Quality of Serv
Page 109 and 110: 5Table 25FieldSNMP Settings (Contin
Page 111 and 112: SNMPConfiguring SNMP on the Access
Page 119 and 120: SNMPSNMP Targets5NOTEAfter you conf
Page 121 and 122: 6AdministrationAdministratorUse thi
Page 123 and 124: 6Access Point ConfigurationThe acce
Page 125 and 126: AdministrationAccess Point Configur
Page 127 and 128: AdministrationSoftware Upgrade6The
Page 129 and 130: AdministrationSoftware Upgrade6The
Page 131 and 132: AdministrationEvent Logs6Click Refr
Page 133 and 134: AdministrationEvent Logs6Configurin
Page 135 and 136: AdministrationConfiguring the Web S
Page 137 and 138: AdministrationCreating an Administr
Page 139 and 140: 7Clustering Multiple Access PointsT
Page 141 and 142: 7Figure 33Cluster Information and M
Page 143 and 144: Clustering Multiple Access PointsMa
Page 149 and 150: Clustering Multiple Access PointsCo
Page 151 and 152: Clustering Multiple Access PointsCo
Page 153 and 154: Clustering Multiple Access PointsVi
Page 155 and 156: Clustering Multiple Access PointsVi
Page 157 and 158:
Clustering Multiple Access PointsVi
Page 159 and 160:
8Configuration ExamplesThis chapter
Page 161 and 162:
8VAP Configuration from the Web Int
Page 163 and 164:
Configuration ExamplesConfiguring W
Page 165 and 166:
Configuration ExamplesConfiguring t
Page 167 and 168:
Configuration ExamplesConfiguring t
Page 169 and 170:
Configuration ExamplesClustering Ac
Page 171 and 172:
ADefault SettingsWhen you first pow
Page 173 and 174:
Default SettingsATable 43UAP Defaul
Page 175 and 176:
BWhere to Go From HereCisco provide
show all

Cisco AP541N Dual-band Single-radio Access Point Administration ...

Create successful ePaper yourself

Delete template?

Save as template?