Roller Chain - Tsubaki

Anti-CorrosiveRoller ChainNeptuneAnti-Corrosive Roller ChainOLL 2 L1ThDRHw TLLDrive ChainAll dimensions in inches unless otherwise stated.RollerDiameterRWidthBetweenInner LinkPlatesWLink Plate PinOffset PinLengthLMinimumTensileStrength(lbs.)AverageTensileStrength(lbs.)MaximumAllowableLoad(lbs.)ApproximateWeight(lbs./ft.)Chain PitchThickness Height Height Diameter Length Length LengthNumber PT H h D L 1 + L 2 L 1 L 2RS35NT 0.375 * 0.200 0.188 0.049 0.354 0.307 0.141 0.500 0.230 0.270 0.531 2,200 2,530 480 0.22 320RS40NT 0.500 0.312 0.313 0.059 0.472 0.409 0.156 0.717 0.325 0.392 0.709 3,960 4,290 810 0.43 240RS50NT 0.625 0.400 0.375 0.079 0.591 0.512 0.200 0.878 0.406 0.472 0.886 6,380 7,040 1,430 0.70 192RS60NT 0.750 0.469 0.500 0.094 0.713 0.614 0.235 1.087 0.506 0.581 1.110 9,020 9,900 1,980 1.03 160RS80NT 1.000 0.625 0.625 0.126 0.949 0.819 0.313 1.398 0.640 0.758 1.524 16,060 17,600 3,300 1.78 120RS100NT 1.250 0.750 0.750 0.157 1.185 1.024 0.376 1.677 0.778 0.900 1.803 23,980 26,400 5,060 2.67 96Note: When 1-pitch offset links are used, the maximum allowable load becomes 60% of the values shown above.* RS35NT is a bushed chain. There are no rollers. The value shown is the bushing diameter.Stainless Steel “SS” Type 304Anti-Corrosive Roller ChainNumberof linksper 10feetOLφ φ RL2LL1CAll dimensions in inches unless otherwise stated.RollerDiameterRWidthBetweenInner LinkPlatesWLink Plate PinOffset PinLengthLTransversePitchCMaximumAllowableLoad(lbs.)ApproximateWeight(lbs./ft.)Chain PitchThickness Height Height Diameter Length Length LengthNumber PT H h D L 1 + L 2 L 1 L 2RS11SS 0.148 * 0.090 0.072 0.015 0.138 0.138 0.062 0.214 0.090 0.125 - - 11 0.03 134RS25SS 0.250 * 0.130 0.125 0.030 0.230 0.199 0.091 0.339 0.150 0.189 - - 26 0.09 160RS35SS 0.375 * 0.200 0.188 0.049 0.354 0.307 0.141 0.500 0.230 0.270 0.579 - 59 0.22 320RS40SS 0.500 0.312 0.313 0.059 0.472 0.409 0.156 0.717 0.325 0.392 0.732 - 99 0.43 240RS40SS-2 0.500 0.312 0.313 0.059 0.472 0.409 0.156 1.283 0.608 0.675 1.319 0.567 198 0.85 240RS50SS 0.625 0.400 0.375 0.079 0.591 0.512 0.200 0.878 0.406 0.472 0.941 - 154 0.70 192RS50SS-2 0.625 0.400 0.375 0.079 0.591 0.512 0.200 1.594 0.762 0.833 1.646 0.713 308 1.39 192RS60SS 0.750 0.469 0.500 0.094 0.713 0.614 0.235 1.087 0.506 0.581 1.157 - 231 1.03 160RS60SS-2 0.750 0.469 0.500 0.094 0.713 0.614 0.235 1.988 0.955 1.033 2.071 0.898 462 2.04 160RS80SS 1.000 0.625 0.625 0.126 0.949 0.819 0.313 1.398 0.640 0.758 1.535 - 396 1.78 120RS80SS-2 1.000 0.625 0.625 0.126 0.949 0.819 0.313 2.551 1.217 1.335 2.679 1.154 792 3.55 120RS100SS 1.250 0.750 0.750 0.157 1.185 1.024 0.376 1.677 0.778 0.900 1.831 - 572 2.69 96RS100SS-2 1.250 0.750 0.750 0.157 1.185 1.024 0.376 3.091 1.484 1.606 3.213 1.409 1,144 5.35 96RS120SS 1.500 0.875 1.000 0.197 1.425 1.228 0.437 2.187 1.014 1.173 2.350 - 858 4.11 80RS120SS-2 1.500 0.875 1.000 0.197 1.425 1.228 0.437 3.961 1.904 2.057 4.130 1.787 1,716 8.19 80RS140SS 1.750 1.000 1.000 0.236 1.661 1.433 0.500 2.406 1.108 1.297 2.606 - 1,034 5.30 68RS140SS-2 1.750 1.000 1.000 0.236 1.661 1.433 0.500 4.331 2.075 2.256 4.512 1.925 2,068 10.57 68RS160SS 2.000 1.125 1.250 0.276 1.898 1.638 0.563 2.839 1.321 1.518 3.043 - 1,430 7.28 60RS160SS-2 2.000 1.125 1.250 0.276 1.898 1.638 0.563 4.965 2.470 2.494 5.303 2.303 2,860 14.51 60RS180SS 2.250 1.406 1.406 0.281 2.059 1.709 0.687 3.091 1.419 1.671 3.343 - 1,918 9.01 54RS200SS 2.500 1.562 1.500 0.315 2.374 2.047 0.781 3.339 1.555 1.783 3.575 - 2,420 11.08 48RS240SS 3.000 1.875 1.875 0.374 2.850 2.457 0.937 4.142 1.870 2.272 4.433 - 3,520 16.42 40* Denotes that sizes RS11SS, RS25SS and RS35SS are rollerless. The values shown are for the bushing diameter. Notes: 1) The link plate thickness of large size chaingreater than RS120SS differs to that of RS Roller Chain. 2) The rivet type for single-strand and multi-strand chain greater than RS80SS is quad rivet.Numberof linksper 10feetA-71