2002 MY OBD-II System Operation Summary - MotorCraftService.com
2002 MY OBD-II System Operation Summary - MotorCraftService.com 2002 MY OBD-II System Operation Summary - MotorCraftService.com
5R44E (RWD) Transmission(has turbine speed sensor)Transmission InputsThe Digital Transmission Range (DTR) sensor provides a single analog and three digital inputs to the PCM. ThePCM decodes these inputs to determine the driver-selected gear position (Park, Rev, Neutral, OD, 2, 1).This input device is checked for opens and invalid input patterns. (P0708 P0705)The Turbine Shaft Speed (TSS) sensor and Output Speed Sensor (OSS) are inputs that are checked forrationality. Provided one of the two speed sensors has sufficient signal and engine load is high enough and theengine speed is above the torque converter stall speed, it can be inferred that the vehicle must be moving. If thereis insufficient output from the TSS sensor, a malfunction is indicated (P0715). If there is insufficient output from theOSS sensor, a malfunction is indicated (P0720).Transmission OutputsShift SolenoidsThe Shift Solenoid (SSA, SSB, SSC, and SSD) output circuits are checked for opens and shorts by the PCM bymonitoring the status of a feedback circuit from the output driver (P0750 SSA, P0755 SSB, P0760 SSC, andP0765 SSD).All vehicle applications will utilize an inductive signature circuit to monitor the shift solenoids functionally. The ISIGcircuit monitors the current signature of the shift solenoid as the solenoid is commanded on. A solenoid thatfunctions properly will show a characteristic decrease in current as the solenoid starts to move. If the solenoid ismalfunctioning, the current will not change (P1714 SSA, P1715 SSB, P1716 SSC, P1717 SSD). The ISIG testruns in conjunction with the other transmission functional tests. The lack of communication between the ISIG chipand the PCM microprocessor is also monitored (P1636).Torque Converter ClutchThe Torque Converter Clutch (TCC) output circuit is a duty-cycled output that is checked electrically for opens andshorts by the PCM by monitoring the status of a feedback circuit from the output driver (P0743).These vehicle applications will utilize an inductive signature circuit to monitor the torque converter clutch. The ISIGcircuit monitors the current signature of the TCC solenoid as the solenoid is commanded on. A solenoid thatfunctions properly will show a characteristic decrease in current as the solenoid starts to move. If the solenoid ismalfunctioning, the current will not change (P1740). The ISIG test is run in conjunction with the other transmissionfunctional tests. The lack of communication between the ISIG chip and the PCM microprocessor is also monitored(P1636).Electronic Pressure Control OutputThe EPC solenoid is a variable force solenoid that controls line pressure in the transmission. The EPC solenoidhas a feedback circuit in the PCM that monitors EPC current. If the current indicates a short to ground (lowpressure), engine torque may be reduced to prevent damage to the transmission. (P1747, PCA)FORD MOTOR COMPANY REVISION DATE: OCTOBER 02, 2001 PAGE 54 OF 66
5R55E (RWD) Transmission(has turbine speed sensor)Transmission InputsThe Digital Transmission Range (DTR) sensor provides a single analog and three digital inputs to the PCM. ThePCM decodes these inputs to determine the driver-selected gear position (Park, Rev, Neutral, OD, 2, 1). This inputdevice is checked for opens and invalid input patterns. (P0708, P0705)The Turbine Shaft Speed (TSS) and Output Shaft Speed (OSS) sensors are inputs that are checked for rationality.Provided one of the twp speed sensors has sufficient signal and engine load is high enough and the engine rpm isabove the torque converter stall speed, it can be inferred that the vehicle must be moving. If there is insufficientoutput from the TSS sensor, a malfunction is indicated (P0715). If there is insufficient output from the OSS sensor,a malfunction is indicated (P0720).Transmission OutputsShift SolenoidsThe Shift Solenoid (SSA, SSB, SSC and SSD) output circuits are checked for opens and shorts by the PCM bymonitoring the status of a feedback circuit from the output driver (P0750 SSA, P0755 SSB, P0760 SSC, P0765SSD).These vehicle applications will utilize an inductive signature circuit to monitor the shift solenoids functionally. TheISIG circuit monitors the current signature of the shift solenoid as the solenoid is commanded on. A solenoid thatfunctions properly will show a characteristic decrease in current as the solenoid starts to move. If the solenoid ismalfunctioning, the current will not change (P1714 SSA, P1715 SSB, P1716 SSC, P1717 SSD). The ISIG test isrun in conjunction with the other transmission functional tests. The lack of communication between the ISIG chipand the PCM microprocessor is also monitored (P1636).Torque Converter ClutchThe Torque Converter Clutch (TCC) output circuit is a duty-cycled output that is checked electrically for opens andshorts by the PCM by monitoring the status of a feedback circuit from the output driver (P0743).These vehicle applications will utilize an inductive signature circuit to monitor the torque converter clutch. The ISIGcircuit monitors the current signature of the TCC solenoid as the solenoid is commanded on. A solenoid thatfunctions properly will show a characteristic decrease in current as the solenoid starts to move. If the solenoid ismalfunctioning, the current will not change (P1740). The ISIG test runs in conjunction with the other transmissionfunctional tests. The lack of communication between the ISIG chip and the PCM microprocessor is also monitored(P1636).Electronic Pressure Control OutputThe EPC solenoid is a variable force solenoid that controls line pressure in the transmission. The EPC solenoidhas a feedback circuit in the PCM that monitors EPC current. If the current indicates a short to ground (lowpressure), engine torque may be reduced to prevent damage to the transmission. (P1747, PCA)FORD MOTOR COMPANY REVISION DATE: OCTOBER 02, 2001 PAGE 55 OF 66
- Page 6 and 7: TYPICAL INDEX RATIO CATALYST MONITO
- Page 8 and 9: Misfire MonitorThere are two differ
- Page 10 and 11: Misfire Monitor Operation:DTCsMonit
- Page 12 and 13: AIR System MonitorThe secondary air
- Page 14 and 15: leed-up criteria is exceeded on thr
- Page 16 and 17: EVAP System Monitor - 0.020” dia.
- Page 18 and 19: Ford’s 0.020” evaporative syste
- Page 20 and 21: Typical 0.020” EVAP abort (fuel s
- Page 22 and 23: Additional malfunctions that are be
- Page 24: HO2S MonitorFront HO2S SignalThe ti
- Page 27 and 28: HO2S Heaters, front and rearThe HO2
- Page 29 and 30: In the 2002 MY, Ford will introduce
- Page 31 and 32: After the vehicle is started, durin
- Page 33 and 34: Finally, the differential pressure
- Page 35 and 36: EGR flow is monitored using an anal
- Page 37 and 38: Typical EGR flow check entry condit
- Page 39 and 40: Comprehensive Component Monitor - E
- Page 41 and 42: Ignition System Check Operation:DTC
- Page 43 and 44: The Intake Manifold Runner Control
- Page 45 and 46: Most vehicle applications no longer
- Page 47 and 48: Transmission Fluid Temperature Sens
- Page 49 and 50: Torque Converter Clutch Check Opera
- Page 51 and 52: 4R70W (RWD) Transmission(no turbine
- Page 53: CD4E (FWD) Transmission(has turbine
- Page 57 and 58: Direct One Way ClutchThe Direct One
- Page 59 and 60: Direct One Way ClutchThe Direct One
- Page 61 and 62: 4F27E (FN) (FWD) Transmission(has t
- Page 63 and 64: Exponentially Weighted Moving Avera
- Page 65 and 66: I/M Readiness CodeThe readiness fun
5R44E (RWD) Transmission(has turbine speed sensor)Transmission InputsThe Digital Transmission Range (DTR) sensor provides a single analog and three digital inputs to the PCM. ThePCM decodes these inputs to determine the driver-selected gear position (Park, Rev, Neutral, OD, 2, 1).This input device is checked for opens and invalid input patterns. (P0708 P0705)The Turbine Shaft Speed (TSS) sensor and Output Speed Sensor (OSS) are inputs that are checked forrationality. Provided one of the two speed sensors has sufficient signal and engine load is high enough and theengine speed is above the torque converter stall speed, it can be inferred that the vehicle must be moving. If thereis insufficient output from the TSS sensor, a malfunction is indicated (P0715). If there is insufficient output from theOSS sensor, a malfunction is indicated (P0720).Transmission OutputsShift SolenoidsThe Shift Solenoid (SSA, SSB, SSC, and SSD) output circuits are checked for opens and shorts by the PCM bymonitoring the status of a feedback circuit from the output driver (P0750 SSA, P0755 SSB, P0760 SSC, andP0765 SSD).All vehicle applications will utilize an inductive signature circuit to monitor the shift solenoids functionally. The ISIGcircuit monitors the current signature of the shift solenoid as the solenoid is <strong>com</strong>manded on. A solenoid thatfunctions properly will show a characteristic decrease in current as the solenoid starts to move. If the solenoid ismalfunctioning, the current will not change (P1714 SSA, P1715 SSB, P1716 SSC, P1717 SSD). The ISIG testruns in conjunction with the other transmission functional tests. The lack of <strong>com</strong>munication between the ISIG chipand the PCM microprocessor is also monitored (P1636).Torque Converter ClutchThe Torque Converter Clutch (TCC) output circuit is a duty-cycled output that is checked electrically for opens andshorts by the PCM by monitoring the status of a feedback circuit from the output driver (P0743).These vehicle applications will utilize an inductive signature circuit to monitor the torque converter clutch. The ISIGcircuit monitors the current signature of the TCC solenoid as the solenoid is <strong>com</strong>manded on. A solenoid thatfunctions properly will show a characteristic decrease in current as the solenoid starts to move. If the solenoid ismalfunctioning, the current will not change (P1740). The ISIG test is run in conjunction with the other transmissionfunctional tests. The lack of <strong>com</strong>munication between the ISIG chip and the PCM microprocessor is also monitored(P1636).Electronic Pressure Control OutputThe EPC solenoid is a variable force solenoid that controls line pressure in the transmission. The EPC solenoidhas a feedback circuit in the PCM that monitors EPC current. If the current indicates a short to ground (lowpressure), engine torque may be reduced to prevent damage to the transmission. (P1747, PCA)FORD MOTOR COMPANY REVISION DATE: OCTOBER 02, 2001 PAGE 54 OF 66