Proline Promass 83E/F/O Operation Manual - FMC Technologies

More documents

Recommendations

Info

Troubleshooting Proline Promass 839.6.1 Removing and installing printed circuit boards#Warning!"Caution!Field housing• Risk of electric shock. Exposed components carry dangerous voltages. Make sure that the powersupply is switched off before you remove the cover of the electronics compartment.• Risk of damaging electronic components (ESD protection). Static electricity can damage electroniccomponents or impair their operability. Use a workplace with a grounded working surfacepurposely built for electrostatically sensitive devices!• If you cannot guarantee that the dielectric strength of the device is maintained in the followingsteps, then an appropriate inspection must be carried out in accordance with the manufacturer’sspecifications.Use only original Endress+Hauser parts.å 47, installation and removal:1. Unscrew cover of the electronics compartment from the transmitter housing.2. Remove the local display (1) as follows:– Press in the latches (1.1) at the side and remove the display module.– Disconnect the ribbon cable (1.2) of the display module from the amplifier board.3. Remove the screws and remove the cover (2) from the electronics compartment.4. Remove power unit board (4) and I/O board (6, 7):Insert a thin pin into the hole (3) provided for the purpose and pull the board clear of its holder.5. Remove submodules (6.1):No tools are required for removing the submodules (inputs/outputs) from the I/O board.Installation is also a no-tools operation." Caution!Only certain combinations of submodules on the I/O board are permissible. ä 29The individual slots are marked and correspond to certain terminals in the connectioncompartment of the transmitter:Slot "INPUT / OUTPUT 2" = Terminals 24 / 25Slot "INPUT / OUTPUT 3" = Terminals 22 / 23Slot "INPUT / OUTPUT 4" = Terminals 20 / 216. Remove amplifier board (5):– Disconnect the plug of the sensor signal cable (5.1) including S-DAT (5.3) from the board.– Gently disconnect the plug of the excitation current cable (5.2) from the board, i.e. withoutmoving it back and forward.– Insert a thin pin into the hole (3) provided for the purpose and pull the board clear of itsholder.7. Installation is the reverse of the removal procedure.Page 96 • MN0M022Issue/Rev. 0.2 (12/12)
Proline Promass 83Troubleshooting4535.165.45.35.233INPUT/OUTPUT 2INPUT/OUTPUT 3INPUT/OUTPUT 46.276.11.2217.11.1Fig. 47: Field housing: removing and installing printed circuit boards1 Local display1.1 Latch1.2 Ribbon cable (display module)2 Screws of electronics compartment cover3 Aperture for installing/removing boards4 Power unit board5 Amplifier board5.1 Signal cable (sensor)5.2 Excitation current cable (sensor)5.3 S-DAT (sensor data memory)5.4 T-DAT (transmitter data memory)6 I/O board (flexible assignment)6.1 F-Chip (function chip for optional software)6.2 Pluggable submodules (status input and current input, current output, frequency output and relay output)7 I/O board (permanent assignment)7.1 F-Chip (function chip for optional software)a0004600Issue/Rev. 0.2 (12/12) MN0M022 • Page 97
Page 1 and 2:
Coriolis Mass FlowmetersProline Pro
Page 3 and 4:
Proline Promass 83Table of contents
Page 5 and 6:
Proline Promass 83Safety instructio
Page 7 and 8:
Proline Promass 83Identification2 I
Page 9 and 10:
Proline Promass 83Identification2.1
Page 11 and 12:
Proline Promass 83Identification2.2
Page 13 and 14:
Proline Promass 83Installation#Warn
Page 15 and 16:
Proline Promass 83InstallationInsta
Page 17 and 18:
Proline Promass 83InstallationOrien
Page 19 and 20:
EscProline Promass 83Installation-
Page 21 and 22:
Proline Promass 83Installation3.2.6
Page 23 and 24:
Proline Promass 83Installation"Caut
Page 25 and 26:
Proline Promass 83Installation3.3.3
Page 27 and 28:
Proline Promass 83Wiring!Note!4.1.2
Page 29 and 30:
Proline Promass 83Wiring4.2.2 Termi
Page 31 and 32:
Proline Promass 83Wiring4.3 Degree
Page 33 and 34:
Proline Promass 83Operation5 Operat
Page 35 and 36:
Proline Promass 83Operation5.1.3 Ic
Page 37 and 38:
Proline Promass 83Operation5.1.4 Co
Page 39 and 40:
Proline Promass 83Operation"Caution
Page 41 and 42:
Proline Promass 83Operation!Note!5.
Page 43 and 44:
Proline Promass 83Operation5.4.2 Cu
Page 45 and 46: Proline Promass 83Operation5.4.4 Un
Page 47 and 48: Proline Promass 83OperationCommand
Page 49 and 50: Proline Promass 83OperationCommand
Page 51 and 52: Proline Promass 83OperationByte-bit
Page 53 and 54: Proline Promass 83Operation#Warning
Page 55 and 56: Proline Promass 83Commissioning6.3
Page 57 and 58: Proline Promass 83Commissioning6.3.
Page 59 and 60: Proline Promass 83CommissioningReco
Page 61 and 62: Proline Promass 83CommissioningFig.
Page 63 and 64: Proline Promass 83CommissioningLow
Page 65 and 66: Proline Promass 83CommissioningReco
Page 67 and 68: Proline Promass 83Commissioning"Cau
Page 69 and 70: Proline Promass 83Commissioning#War
Page 71 and 72: Proline Promass 83CommissioningFig.
Page 73 and 74: Proline Promass 83CommissioningExam
Page 77 and 78: Proline Promass 83Commissioning6.5
Page 81 and 82: Proline Promass 83Commissioning#War
Page 83 and 84: Proline Promass 83Accessories8 Acce
Page 85 and 86: Proline Promass 83AccessoriesAccess
Page 87 and 88: Proline Promass 83äTroubleshooting
Page 89 and 90: Proline Promass 83äTroubleshooting
Page 91 and 92: Proline Promass 83Troubleshooting!N
Page 93 and 94: Proline Promass 83Troubleshooting9.
Page 95: Proline Promass 83Troubleshooting!N
Page 99 and 100: Proline Promass 83TroubleshootingFi
Page 101 and 102: Proline Promass 83Troubleshooting"C
Page 103 and 104: Proline Promass 83Technical data10
Page 105 and 106: Proline Promass 83Technical dataMea
Page 107 and 108: Proline Promass 83Technical data10.
Page 109 and 110: Proline Promass 83Technical dataFlo
Page 113 and 114: Proline Promass 83Technical dataZer
Page 115 and 116: Proline Promass 83Technical dataPer
Page 117 and 118: Proline Promass 83Technical dataDes
Page 119 and 120: Proline Promass 83Technical dataInf
Page 121 and 122: Proline Promass 83Technical dataRep
Page 131 and 132: Proline Promass 83Limiting flowPres
Page 133 and 134: Proline Promass 83Technical dataPre
Page 143 and 144: Proline Promass 83Technical dataPro
Page 145 and 146: Proline Promass 83Technical dataPro
Page 147 and 148:
Proline Promass 83Technical data10.
Page 149 and 150:
Proline Promass 83AAccessories . .
Page 151 and 152:
Proline Promass 83SealsMaterial. .
Page 153 and 154:
Declaration of Hazardous Material a
show all

Proline Promass 83E/F/O Operation Manual - FMC Technologies

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?