Proline Promass 83E/F/O Operation Manual - FMC Technologies

More documents

Recommendations

Info

Commissioning Proline Promass 83Performing a zero point adjustment1. Let the system run until operating conditions have been reached.2. Stop the flow (v = 0 m/s).3. Check the shutoff valves for leaks.4. Check that operating pressure is correct.5. Perform a zero point adjustment as follows:Key Procedure Display textFPPPHOME position Enter the function matrixSelect the BASIC FUNCTION blockSelect the PROCESS PARAMETER groupSelect the ADJUSTMENT function group> GROUP SELECTION GROUP SELECTION GROUP SELECTION GROUP SELECTION
Proline Promass 83Commissioning6.5.2 Density adjustmentIt is advisable to perform a density adjustment when optimum measuring accuracy is required forcalculating density dependent values. The application may require a 1-point or 2-point densityadjustment.1-point density adjustment (with one fluid):This type of density adjustment is necessary under the following circumstances:• The sensor does not measure exactly the density value that the user expects on the basis oflaboratory analyses.• The fluid properties are outside the measuring points set at the factory, or the reference operatingconditions used to calibrate the measuring device.• The system is used exclusively to measure a fluid’s density which must be registered to a highdegree of accuracy under constant conditions.Example: Brix density measurement for apple juice.2-point density adjustment (with two fluids):This type of adjustment is always to be carried out if the measuring tubes have been mechanicallyaltered by, e.g. material buildup, abrasion or corrosion. In such cases, the resonant frequency of themeasuring tubes has been affected by these factors and is no longer compatible with the calibrationdata set at the factory. The 2-point density adjustment takes these mechanically-based changes intoaccount and calculates new, adjusted calibration data."Caution!Performing a 1-point or 2-point density adjustment• Onsite density adjustment can be performed only if the user has detailed knowledge of the fluiddensity, obtained for example from detailed laboratory analyses.• The target density value specified in this way must not deviate from the measured fluid densityby more than ±10%.• An error in defining the target density affects all calculated density and volume functions.• The 2-point density adjustment is only possible if both target density values are different fromeach other by at least 0.2 kg/l. Otherwise the error message #731 (adjustment is not possible)appears in the "Diag. - Act. Sys. Condition" parameter.• Density adjustment changes the factory density calibration values or the calibration values set bythe service technician.• The functions outlined in the following instructions are described in detail in the "Description ofDevice Functions" manual.1. Fill the sensor with fluid. Make sure that the measuring tubes are completely filled and thatliquids are free of gas bubbles.2. Wait until the temperature difference between fluid and measuring tube has equalized. Thetime you have to wait for equalization depends on the fluid and the temperature level.O S3. Using the local display, select the SETPOINT DENSITY Ffunctionin the function matrix andperform density adjustment as follows:FunctionNo.Function name Setting to be selected ( O or S )(to next function with F )6482 DENSITY ADJUST MODE Use P to select a 1- or 2-point adjustment.! Note!When you press P you are automatically prompted to enter the accesscode if the function matrix is still disabled. Enter the code.6483 DENSITY SET VALUE 1 Use P to enter the target density of the first fluid and press F to savethis value (input range = actual density value ±10%).Issue/Rev. 0.2 (12/12) MN0M022 • Page 79
Page 1 and 2:
Coriolis Mass FlowmetersProline Pro
Page 3 and 4:
Proline Promass 83Table of contents
Page 5 and 6:
Proline Promass 83Safety instructio
Page 7 and 8:
Proline Promass 83Identification2 I
Page 9 and 10:
Proline Promass 83Identification2.1
Page 11 and 12:
Proline Promass 83Identification2.2
Page 13 and 14:
Proline Promass 83Installation#Warn
Page 15 and 16:
Proline Promass 83InstallationInsta
Page 17 and 18:
Proline Promass 83InstallationOrien
Page 19 and 20:
EscProline Promass 83Installation-
Page 21 and 22:
Proline Promass 83Installation3.2.6
Page 23 and 24:
Proline Promass 83Installation"Caut
Page 25 and 26:
Proline Promass 83Installation3.3.3
Page 27 and 28: Proline Promass 83Wiring!Note!4.1.2
Page 29 and 30: Proline Promass 83Wiring4.2.2 Termi
Page 31 and 32: Proline Promass 83Wiring4.3 Degree
Page 33 and 34: Proline Promass 83Operation5 Operat
Page 35 and 36: Proline Promass 83Operation5.1.3 Ic
Page 37 and 38: Proline Promass 83Operation5.1.4 Co
Page 39 and 40: Proline Promass 83Operation"Caution
Page 41 and 42: Proline Promass 83Operation!Note!5.
Page 43 and 44: Proline Promass 83Operation5.4.2 Cu
Page 45 and 46: Proline Promass 83Operation5.4.4 Un
Page 47 and 48: Proline Promass 83OperationCommand
Page 49 and 50: Proline Promass 83OperationCommand
Page 51 and 52: Proline Promass 83OperationByte-bit
Page 53 and 54: Proline Promass 83Operation#Warning
Page 55 and 56: Proline Promass 83Commissioning6.3
Page 57 and 58: Proline Promass 83Commissioning6.3.
Page 59 and 60: Proline Promass 83CommissioningReco
Page 61 and 62: Proline Promass 83CommissioningFig.
Page 63 and 64: Proline Promass 83CommissioningLow
Page 65 and 66: Proline Promass 83CommissioningReco
Page 67 and 68: Proline Promass 83Commissioning"Cau
Page 69 and 70: Proline Promass 83Commissioning#War
Page 71 and 72: Proline Promass 83CommissioningFig.
Page 73 and 74: Proline Promass 83CommissioningExam
Page 75 and 76: Proline Promass 83Commissioning6.4.
Page 77: Proline Promass 83Commissioning6.5
Page 81 and 82: Proline Promass 83Commissioning#War
Page 83 and 84: Proline Promass 83Accessories8 Acce
Page 85 and 86: Proline Promass 83AccessoriesAccess
Page 87 and 88: Proline Promass 83äTroubleshooting
Page 89 and 90: Proline Promass 83äTroubleshooting
Page 91 and 92: Proline Promass 83Troubleshooting!N
Page 93 and 94: Proline Promass 83Troubleshooting9.
Page 95 and 96: Proline Promass 83Troubleshooting!N
Page 97 and 98: Proline Promass 83Troubleshooting45
Page 99 and 100: Proline Promass 83TroubleshootingFi
Page 101 and 102: Proline Promass 83Troubleshooting"C
Page 103 and 104: Proline Promass 83Technical data10
Page 105 and 106: Proline Promass 83Technical dataMea
Page 107 and 108: Proline Promass 83Technical data10.
Page 109 and 110: Proline Promass 83Technical dataFlo
Page 113 and 114: Proline Promass 83Technical dataZer
Page 115 and 116: Proline Promass 83Technical dataPer
Page 117 and 118: Proline Promass 83Technical dataDes
Page 119 and 120: Proline Promass 83Technical dataInf
Page 121 and 122: Proline Promass 83Technical dataRep
Page 129 and 130:
Proline Promass 83Technical data10.
Page 131 and 132:
Proline Promass 83Limiting flowPres
Page 133 and 134:
Proline Promass 83Technical dataPre
Page 135 and 136:
Page 137 and 138:
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
Proline Promass 83Technical dataPro
Page 145 and 146:
Proline Promass 83Technical dataPro
Page 147 and 148:
Page 149 and 150:
Proline Promass 83AAccessories . .
Page 151 and 152:
Proline Promass 83SealsMaterial. .
Page 153 and 154:
Declaration of Hazardous Material a
show all

Proline Promass 83E/F/O Operation Manual - FMC Technologies

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?