Proline Promass 83E/F/O Operation Manual - FMC Technologies

More documents

Recommendations

Info

Operation Proline Promass 835.4.3 Device and process variablesDevice variables:The following device variables are available using the HART protocol:Code (decimal) Device variable Code (decimal) Device variable0 OFF (unassigned) 26 °PLATO2 Mass flow 27 °BALLING5 Volume flow 28 °BRIX6 Corrected volume flow 29 Other7 Density 52 Batch up8 Reference density 53 Batch down9 Temperature 58 Mass flow deviation12 Target mass flow 59 Density deviation13 % Target mass flow 60 Reference density deviation14 Target volume flow 61 Temperature deviation15 % Target volume flow 62 Tube damping deviation16 Target corrected volume flow 63 Electrodyn. sensor deviation17 Carrier mass flow 64 Dynamic viscosity18 % Carrier mass flow 65 Kinematic viscosity19 Carrier volume flow 81 Temp. comp. dyn. viscosity20 % carrier volume flow 82 Temp. comp. kin. viscosity21 Carrier corrected volume flow 86 Operating frequency fluctuation22 %-BLACK LIQUOR 87 Tube damping fluctuation23 °BAUME >1kg/l 250 Totalizer 124 °BAUME
Proline Promass 83Operation5.4.4 Universal / Common practice HART commandsThe following table contains all the universal commands supported by the device.Command No.HART command / Access typeUniversal Commands0 Read unique device identifierAccess type = read1 Read primary process variableAccess type = read2 Read the primary process variable ascurrent in mA and percentage of theset measuring rangeAccess type = read3 Read the primary process variable ascurrent in mA and four (presetusing Command 51) dynamicprocess variablesAccess type = readCommand data(numeric data in decimal form)nonenonenonenoneResponse data(numeric data in decimal form)Device identification delivers information on the deviceand the manufacturer. It cannot be changed.The response consists of a 12-byte device ID:– Byte 0: Fixed value 254– Byte 1: Manufacturer ID, 17 = E+H– Byte 2: Device type ID, e.g. 81 = Promass 83or 80 = Promass 80– Byte 3: Number of preambles– Byte 4: Universal commands rev. no.– Byte 5: Device-spec. commands rev. no.– Byte 6: Software revision– Byte 7: Hardware revision– Byte 8: Additional device information– Byte 9-11: Device identification– Byte 0: HART unit code of the primary processvariable– Bytes 1-4: Primary process variableFactory setting:Primary process variable = Mass flow! Note!• You can set the assignment of device variables toprocess variables using Command 51.• Manufacturer-specific units are represented using theHART unit code "240".– Bytes 0-3: Actual current of the primary processvariable in mA– Bytes 4-7: Percentage of the set measuring rangeFactory setting:Primary process variable = Mass flow! Note!You can set the assignment of device variables to processvariables using Command 51.24 bytes are sent as a response:– Bytes 0-3: Primary process variable current in mA– Byte 4: HART unit code of the primary processvariable– Bytes 5-8: Primary process variable– Byte 9: HART unit code of the second process variable– Bytes 10-13: Second process variable– Byte 14: HART unit code of the third process variable– Bytes 15-18: Third process variable– Byte 19: HART unit code of the fourth processvariable– Bytes 20-23: Fourth process variableFactory setting:• Primary process variable = Mass flow• Second process variable = Totalizer 1• Third process variable = Density• Fourth process variable = Temperature! Note!• You can set the assignment of device variables toprocess variables using Command 51.• Manufacturer-specific units are represented using theHART unit code "240".Issue/Rev. 0.2 (12/12) MN0M022 • Page 45
Page 1 and 2: Coriolis Mass FlowmetersProline Pro
Page 3 and 4: Proline Promass 83Table of contents
Page 5 and 6: Proline Promass 83Safety instructio
Page 7 and 8: Proline Promass 83Identification2 I
Page 9 and 10: Proline Promass 83Identification2.1
Page 11 and 12: Proline Promass 83Identification2.2
Page 13 and 14: Proline Promass 83Installation#Warn
Page 15 and 16: Proline Promass 83InstallationInsta
Page 17 and 18: Proline Promass 83InstallationOrien
Page 19 and 20: EscProline Promass 83Installation-
Page 21 and 22: Proline Promass 83Installation3.2.6
Page 23 and 24: Proline Promass 83Installation"Caut
Page 25 and 26: Proline Promass 83Installation3.3.3
Page 27 and 28: Proline Promass 83Wiring!Note!4.1.2
Page 29 and 30: Proline Promass 83Wiring4.2.2 Termi
Page 31 and 32: Proline Promass 83Wiring4.3 Degree
Page 33 and 34: Proline Promass 83Operation5 Operat
Page 35 and 36: Proline Promass 83Operation5.1.3 Ic
Page 37 and 38: Proline Promass 83Operation5.1.4 Co
Page 39 and 40: Proline Promass 83Operation"Caution
Page 41 and 42: Proline Promass 83Operation!Note!5.
Page 43: Proline Promass 83Operation5.4.2 Cu
Page 47 and 48: Proline Promass 83OperationCommand
Page 49 and 50: Proline Promass 83OperationCommand
Page 51 and 52: Proline Promass 83OperationByte-bit
Page 53 and 54: Proline Promass 83Operation#Warning
Page 55 and 56: Proline Promass 83Commissioning6.3
Page 57 and 58: Proline Promass 83Commissioning6.3.
Page 59 and 60: Proline Promass 83CommissioningReco
Page 61 and 62: Proline Promass 83CommissioningFig.
Page 63 and 64: Proline Promass 83CommissioningLow
Page 65 and 66: Proline Promass 83CommissioningReco
Page 67 and 68: Proline Promass 83Commissioning"Cau
Page 69 and 70: Proline Promass 83Commissioning#War
Page 71 and 72: Proline Promass 83CommissioningFig.
Page 73 and 74: Proline Promass 83CommissioningExam
Page 77 and 78: Proline Promass 83Commissioning6.5
Page 81 and 82: Proline Promass 83Commissioning#War
Page 83 and 84: Proline Promass 83Accessories8 Acce
Page 85 and 86: Proline Promass 83AccessoriesAccess
Page 87 and 88: Proline Promass 83äTroubleshooting
Page 89 and 90: Proline Promass 83äTroubleshooting
Page 91 and 92: Proline Promass 83Troubleshooting!N
Page 93 and 94: Proline Promass 83Troubleshooting9.
Page 95 and 96:
Proline Promass 83Troubleshooting!N
Page 97 and 98:
Proline Promass 83Troubleshooting45
Page 99 and 100:
Proline Promass 83TroubleshootingFi
Page 101 and 102:
Proline Promass 83Troubleshooting"C
Page 103 and 104:
Proline Promass 83Technical data10
Page 105 and 106:
Proline Promass 83Technical dataMea
Page 107 and 108:
Proline Promass 83Technical data10.
Page 109 and 110:
Proline Promass 83Technical dataFlo
Page 111 and 112:
Page 113 and 114:
Proline Promass 83Technical dataZer
Page 115 and 116:
Proline Promass 83Technical dataPer
Page 117 and 118:
Proline Promass 83Technical dataDes
Page 119 and 120:
Proline Promass 83Technical dataInf
Page 121 and 122:
Proline Promass 83Technical dataRep
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
Page 131 and 132:
Proline Promass 83Limiting flowPres
Page 133 and 134:
Proline Promass 83Technical dataPre
Page 135 and 136:
Page 137 and 138:
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
Proline Promass 83Technical dataPro
Page 145 and 146:
Proline Promass 83Technical dataPro
Page 147 and 148:
Page 149 and 150:
Proline Promass 83AAccessories . .
Page 151 and 152:
Proline Promass 83SealsMaterial. .
Page 153 and 154:
Declaration of Hazardous Material a
show all

Proline Promass 83E/F/O Operation Manual - FMC Technologies

Create successful ePaper yourself

Delete template?

Save as template?