Proline Promass 83E/F/O Operation Manual - FMC Technologies

More documents

Recommendations

Info

Operation Proline Promass 83Icon Meaning Icon MeaningBatching quantity upwardsBatching quantity downwardsa0001201a0001202Batch quantityTotal batching quantitya0001203a0001204Batch counter (x times)Fluid temperaturea0001205a0001207Current inputRemote configurationActive device operation via:• HART, e.g. FieldCare, DXR 375a0001209a0001206Page 36 • MN0M022Issue/Rev. 0.2 (12/12)
Proline Promass 83Operation5.1.4 Controlling the batching processes using the local displayFilling processes can be controlled directly by means of the local display with the aid of the optional"(Batching)" software package (F-CHIP, accessories ä 83). Therefore, the device can be fullydeployed in the field as a "batch controller".Procedure:1. Configure all the required batching functions and assign the lower display info line (=BATCHING KEYS) using the "Batch" Quick Setup menu (ä 60) or using the functionmatrix (ä 38).The following "softkeys" then appear on the bottom line of the local display å 30:– START = left display key (S)– PRESET = middle display key (O)– MATRIX = right display key (F)2. Press the "PRESET (O)" key. Various batching process functions requiring configuration willnow appear on the display:"PRESET" Initial settings for the batching processNo. Function Configuration7200 BATCH SELECTOR OS Select the batching liquid (BATCH #1 to 6)7203 BATCH QUANTITY If the "ACCESS CUSTOMER" option was selected for the "PRESETbatch quantity" prompt in the "Batching" Quick Setup, the batchingquantity can be altered via the local display. If the "LOCKED" optionwas selected, the batching quantity can only be read and cannot bealtered until the private code has been entered.7265 RESET TOTAL BATCH SUM/COUNTERResets the batching quantity counter or the total batching quantity to"0".3. After exiting the PRESET menu, you can now start the batching process by pressing "START(S)". New softkeys (STOP / HOLD or GO ON) now appear on the display. You can use theseto interrupt, continue or stop the batching process at any time. å 30STOP (S) Stops batching processHOLD (O) Interrupts batching process (softkey changes to "GO ON")GO ON (O) Continues batching process (softkey changes to "HOLD")After the batch quantity is reached, the "START" or "PRESET" softkeys reappear on the display.Fig. 30:Controlling batching processes using the local display (softkeys)Issue/Rev. 0.2 (12/12) MN0M022 • Page 37
Page 1 and 2: Coriolis Mass FlowmetersProline Pro
Page 3 and 4: Proline Promass 83Table of contents
Page 5 and 6: Proline Promass 83Safety instructio
Page 7 and 8: Proline Promass 83Identification2 I
Page 9 and 10: Proline Promass 83Identification2.1
Page 11 and 12: Proline Promass 83Identification2.2
Page 13 and 14: Proline Promass 83Installation#Warn
Page 15 and 16: Proline Promass 83InstallationInsta
Page 17 and 18: Proline Promass 83InstallationOrien
Page 19 and 20: EscProline Promass 83Installation-
Page 21 and 22: Proline Promass 83Installation3.2.6
Page 23 and 24: Proline Promass 83Installation"Caut
Page 25 and 26: Proline Promass 83Installation3.3.3
Page 27 and 28: Proline Promass 83Wiring!Note!4.1.2
Page 29 and 30: Proline Promass 83Wiring4.2.2 Termi
Page 31 and 32: Proline Promass 83Wiring4.3 Degree
Page 33 and 34: Proline Promass 83Operation5 Operat
Page 35: Proline Promass 83Operation5.1.3 Ic
Page 39 and 40: Proline Promass 83Operation"Caution
Page 41 and 42: Proline Promass 83Operation!Note!5.
Page 43 and 44: Proline Promass 83Operation5.4.2 Cu
Page 45 and 46: Proline Promass 83Operation5.4.4 Un
Page 47 and 48: Proline Promass 83OperationCommand
Page 49 and 50: Proline Promass 83OperationCommand
Page 51 and 52: Proline Promass 83OperationByte-bit
Page 53 and 54: Proline Promass 83Operation#Warning
Page 55 and 56: Proline Promass 83Commissioning6.3
Page 57 and 58: Proline Promass 83Commissioning6.3.
Page 59 and 60: Proline Promass 83CommissioningReco
Page 61 and 62: Proline Promass 83CommissioningFig.
Page 63 and 64: Proline Promass 83CommissioningLow
Page 65 and 66: Proline Promass 83CommissioningReco
Page 67 and 68: Proline Promass 83Commissioning"Cau
Page 69 and 70: Proline Promass 83Commissioning#War
Page 71 and 72: Proline Promass 83CommissioningFig.
Page 73 and 74: Proline Promass 83CommissioningExam
Page 77 and 78: Proline Promass 83Commissioning6.5
Page 81 and 82: Proline Promass 83Commissioning#War
Page 83 and 84: Proline Promass 83Accessories8 Acce
Page 85 and 86: Proline Promass 83AccessoriesAccess
Page 87 and 88:
Proline Promass 83äTroubleshooting
Page 89 and 90:
Proline Promass 83äTroubleshooting
Page 91 and 92:
Proline Promass 83Troubleshooting!N
Page 93 and 94:
Proline Promass 83Troubleshooting9.
Page 95 and 96:
Proline Promass 83Troubleshooting!N
Page 97 and 98:
Proline Promass 83Troubleshooting45
Page 99 and 100:
Proline Promass 83TroubleshootingFi
Page 101 and 102:
Proline Promass 83Troubleshooting"C
Page 103 and 104:
Proline Promass 83Technical data10
Page 105 and 106:
Proline Promass 83Technical dataMea
Page 107 and 108:
Proline Promass 83Technical data10.
Page 109 and 110:
Proline Promass 83Technical dataFlo
Page 111 and 112:
Page 113 and 114:
Proline Promass 83Technical dataZer
Page 115 and 116:
Proline Promass 83Technical dataPer
Page 117 and 118:
Proline Promass 83Technical dataDes
Page 119 and 120:
Proline Promass 83Technical dataInf
Page 121 and 122:
Proline Promass 83Technical dataRep
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
Page 131 and 132:
Proline Promass 83Limiting flowPres
Page 133 and 134:
Proline Promass 83Technical dataPre
Page 135 and 136:
Page 137 and 138:
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
Proline Promass 83Technical dataPro
Page 145 and 146:
Proline Promass 83Technical dataPro
Page 147 and 148:
Page 149 and 150:
Proline Promass 83AAccessories . .
Page 151 and 152:
Proline Promass 83SealsMaterial. .
Page 153 and 154:
Declaration of Hazardous Material a
show all

Proline Promass 83E/F/O Operation Manual - FMC Technologies

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?