Proline Promass 83E/F/O Operation Manual - FMC Technologies

More documents

Recommendations

Info

Wiring Proline Promass 834.4 Post-connection checkPerform the following checks after completing electrical installation of the measuring device:Device condition and specificationsNotesAre cables or the device damaged (visual inspection)? -Electrical connectionDoes the supply voltage match the specifications on the nameplate?Notes85 to 260 V AC (45 to 65 Hz)20 to 55 V AC (45 to 65 Hz)16 to 62 V DCDo the cables comply with the specifications? ä 27Do the cables have adequate strain relief? -Cables correctly segregated by type?Without loops and crossovers?Are the power supply and signal cables correctly connected?-See the wiring diagram insidethe cover of the terminalcompartmentAre all screw terminals firmly tightened? -Are all cable entries installed, firmly tightened and correctly sealed?Cables looped as "water traps"?ä 31Are all housing covers installed and firmly tightened? -Page 32 • MN0M022Issue/Rev. 0.2 (12/12)
Proline Promass 83Operation5 Operation5.1 Display and operating elementsThe local display enables you to read all important parameters directly at the measuring point andconfigure the device using the "Quick Setup" or the function matrix.The display consists of four lines; this is where measured values and/or status variables (directionof flow, empty pipe, bar graph, etc.) are displayed. You can change the assignment of display linesto different variables to suit your needs and preferences ( see the "Description of DeviceFunctions" manual).Fig. 28: Display and operating elements1 Liquid crystal displayThe backlit, four-line liquid crystal display shows measured values, dialog texts, fault messages and noticemessages. HOME position (operating mode) is the term given to the display during normal operation.Readings displayed2 Optical sensors for "Touch Control"3 Plus/minus keys– HOME position Direct access to totalizer values and actual values of inputs/outputs– Enter numerical values, select parameters– Select different blocks, groups and function groups within the function matrixPress the +/ keys (X) simultaneously to trigger the following functions::– Exit the function matrix step by step HOME position– Press and hold down +/ keys for longer than 3 seconds Return directly to HOME position– Cancel data entry4 Enter key– HOME position Entry into the function matrix– Save the numerical values you input or settings you changeIssue/Rev. 0.2 (12/12) MN0M022 • Page 33
Page 1 and 2: Coriolis Mass FlowmetersProline Pro
Page 3 and 4: Proline Promass 83Table of contents
Page 5 and 6: Proline Promass 83Safety instructio
Page 7 and 8: Proline Promass 83Identification2 I
Page 9 and 10: Proline Promass 83Identification2.1
Page 11 and 12: Proline Promass 83Identification2.2
Page 13 and 14: Proline Promass 83Installation#Warn
Page 15 and 16: Proline Promass 83InstallationInsta
Page 17 and 18: Proline Promass 83InstallationOrien
Page 19 and 20: EscProline Promass 83Installation-
Page 21 and 22: Proline Promass 83Installation3.2.6
Page 23 and 24: Proline Promass 83Installation"Caut
Page 25 and 26: Proline Promass 83Installation3.3.3
Page 27 and 28: Proline Promass 83Wiring!Note!4.1.2
Page 29 and 30: Proline Promass 83Wiring4.2.2 Termi
Page 31: Proline Promass 83Wiring4.3 Degree
Page 35 and 36: Proline Promass 83Operation5.1.3 Ic
Page 37 and 38: Proline Promass 83Operation5.1.4 Co
Page 39 and 40: Proline Promass 83Operation"Caution
Page 41 and 42: Proline Promass 83Operation!Note!5.
Page 43 and 44: Proline Promass 83Operation5.4.2 Cu
Page 45 and 46: Proline Promass 83Operation5.4.4 Un
Page 47 and 48: Proline Promass 83OperationCommand
Page 49 and 50: Proline Promass 83OperationCommand
Page 51 and 52: Proline Promass 83OperationByte-bit
Page 53 and 54: Proline Promass 83Operation#Warning
Page 55 and 56: Proline Promass 83Commissioning6.3
Page 57 and 58: Proline Promass 83Commissioning6.3.
Page 59 and 60: Proline Promass 83CommissioningReco
Page 61 and 62: Proline Promass 83CommissioningFig.
Page 63 and 64: Proline Promass 83CommissioningLow
Page 65 and 66: Proline Promass 83CommissioningReco
Page 67 and 68: Proline Promass 83Commissioning"Cau
Page 69 and 70: Proline Promass 83Commissioning#War
Page 71 and 72: Proline Promass 83CommissioningFig.
Page 73 and 74: Proline Promass 83CommissioningExam
Page 77 and 78: Proline Promass 83Commissioning6.5
Page 81 and 82: Proline Promass 83Commissioning#War
Page 83 and 84:
Proline Promass 83Accessories8 Acce
Page 85 and 86:
Proline Promass 83AccessoriesAccess
Page 87 and 88:
Proline Promass 83äTroubleshooting
Page 89 and 90:
Proline Promass 83äTroubleshooting
Page 91 and 92:
Proline Promass 83Troubleshooting!N
Page 93 and 94:
Proline Promass 83Troubleshooting9.
Page 95 and 96:
Proline Promass 83Troubleshooting!N
Page 97 and 98:
Proline Promass 83Troubleshooting45
Page 99 and 100:
Proline Promass 83TroubleshootingFi
Page 101 and 102:
Proline Promass 83Troubleshooting"C
Page 103 and 104:
Proline Promass 83Technical data10
Page 105 and 106:
Proline Promass 83Technical dataMea
Page 107 and 108:
Proline Promass 83Technical data10.
Page 109 and 110:
Proline Promass 83Technical dataFlo
Page 111 and 112:
Page 113 and 114:
Proline Promass 83Technical dataZer
Page 115 and 116:
Proline Promass 83Technical dataPer
Page 117 and 118:
Proline Promass 83Technical dataDes
Page 119 and 120:
Proline Promass 83Technical dataInf
Page 121 and 122:
Proline Promass 83Technical dataRep
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
Page 131 and 132:
Proline Promass 83Limiting flowPres
Page 133 and 134:
Proline Promass 83Technical dataPre
Page 135 and 136:
Page 137 and 138:
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
Proline Promass 83Technical dataPro
Page 145 and 146:
Proline Promass 83Technical dataPro
Page 147 and 148:
Page 149 and 150:
Proline Promass 83AAccessories . .
Page 151 and 152:
Proline Promass 83SealsMaterial. .
Page 153 and 154:
Declaration of Hazardous Material a
show all

Proline Promass 83E/F/O Operation Manual - FMC Technologies

Create successful ePaper yourself

Delete template?

Save as template?