Download - Xerox Support and Drivers

More documents

Recommendations

Info

Configuring TCP/IPYour printer can be set up with a variety of TCP/IP network information,such as an IP address, a subnet mask, a gateway, and DNS addresses.There are several ways in which your printer can be assigned a TCP/IPaddress, depending on your network.• Static addressing: A TCP/IP address is assigned manually by thesystem administrator.• Dynamic addressing via BOOTP/DHCP (default): A TCP/IP addressis assigned automatically by the server.NoteBefore configuring TCP/IP, you need to set the networkprotocol to TCP/IP.Static addressingTo enter a TCP/IP address from your printer’s control panel, take thefollowing step:1 Press Menu until Network appears on the bottom line of thedisplay and press OK.2 Press OK when TCP/IP appears.3 Press the Scroll buttons until Static appears and press OK.4 Press OK when IP Address appears.5 Set the first byte between 0 and 255 using the Scroll buttons andpress OK to move to the next byte.Repeat this to complete the address from the 1st byte to the 4thbyte.6 When you have finished, press OK.7 Repeat step 5 and 6 to configure the other TCP/IP parameters:subnet mask and gateway address.8 Press Stop to return to Standby mode.Dynamic addressing (BOOTP/DHCP)To have a TCP/IP address assigned automatically by the server, take thefollowing step:1 Press Menu until Network appears on the bottom line of thedisplay.Configuring EtherTalkEtherTalk is AppleTalk used in an Ethernet network. This protocol iswidely used in Macintosh network environments. To use EtherTalk, takethe following step:1 Press Menu until Network appears on the bottom line of thedisplay and press OK.2 Press the Scroll buttons until EtherTalk appears and press OK.3 Press the Scroll buttons until On appears and press OK.4 Press Stop to return to Standby mode.Configuring IPX frame typesTo use IPX/SPX protocol networks (for example, Novell NetWare), theformat of the network communication frames must be specified for theprinter. In most cases, you can keep the Auto setting. However, you canmanually set the frame type format, if required. Take the following stepto change the frame type format:1 Press Menu until Network on the bottom line of the display andpress OK.2 Press the Scroll buttons until NetWare appears and press OK.3 Press the Scroll buttons until the desired frame type appears.• Auto: Automatically senses and limits the frame type to the firstone detected.• 802.2: Limits the frame type to IPX over IEEE 802.2 with IEEE802.3 frames. All others will be discarded.• 802.3: Limits the frame type to IPX over IEEE 802.3 frames. Allothers will be discarded.• Ethernet II: Limits the frame type to IPX over Ethernet Frames. Allothers will be discarded.• SNAP: Limits the frame type to IPX over SNAP with IEEE 802.3frames. All others will be discarded.• Off: The IPX/SPX protocol is disabled.4 Press OK to save the selection.5 Press Stop to return to Standby mode.2 Press OK when TCP/IP appears.3 Press the Scroll buttons until DHCP or BOOTP appears and pressOK.4 Press Stop to return to Standby mode.4.2
Setting Ethernet speedYou can select the communication speed for Ethernet connections.1 Press Menu until Network appears on the bottom line of thedisplay and press OK.2 Press the Scroll buttons until Ethernet Speed appears and pressOK.3 Press the Scroll buttons until the speed you want appears andpress OK.4 Press Stop to return to Standby mode.Restoring the network configurationYou can return the network configuration to its default settings.1 Press Menu until Network appears on the bottom line of thedisplay and press OK.2 Press the Scroll buttons until Clear Setting appears and pressOK.3 Press OK when Yes appears to restore the network configuration.4 Power the printer off and back on.Printing a network configuration pageThe network configuration page shows how the network interface cardon your printer is configured.1 Press Menu until Network appears on the bottom line of thedisplay and press OK.2 Press the Scroll buttons until Network Info. appears and pressOK.3 Press OK when Yes appears.The network configuration page prints out.4.3
Page 2 and 3: This manual is provided for informa
Page 4 and 5: 8. MaintenancePrinting information
Page 6 and 7: - The power cord is damaged or fray
Page 8 and 9: Environmental ComplianceUSAEnergy S
Page 10 and 11: 1 IntroductionCongratulations on th
Page 12 and 13: Rear viewControl panel overview1 St
Page 14 and 15: 2 System setupThis chapter provides
Page 16 and 17: Paper menuUse the Paper menu to def
Page 18 and 19: Emulation menuUse the Emulation men
Page 20 and 21: Using toner save modeToner save mod
Page 22 and 23: Printer driver featuresYour printer
Page 26 and 27: 5 Loading print mediaThis chapter w
Page 28 and 29: Guidelines for selecting and storin
Page 30 and 31: Using the tray 1 or the optional tr
Page 32 and 33: For information about setting the p
Page 34 and 35: 6 Basic printingThis chapter explai
Page 36 and 37: 8 MaintenanceThis chapter provides
Page 38 and 39: Redistributing toner cartridgeWhen
Page 40 and 41: 9 TroubleshootingThis chapter provi
Page 42 and 43: Around the toner cartridgeNoteThe f
Page 44 and 45: 2 Remove the jammed paper from the
Page 46 and 47: Understanding display messagesMessa
Page 48 and 49: Solving general printing problemsFo
Page 50 and 51: Condition Possible cause Suggested
Page 52 and 53: ConditionSuggested solutionsConditi
Page 54 and 55: 10 Installing accessoriesYour print
Page 56 and 57: 11 SpecificationsThis chapter inclu
Page 58 and 59: maintaining 8.2redistributing 8.3re
Page 60 and 61: SOFTWARE SECTIONCONTENTSChapter 1:
Page 62 and 63: Chapter 8: USING YOUR PRINTER WITH
Page 64 and 65: NOTE: If your printer is not alread
Page 66 and 67: 5 The list of printers available on
Page 68 and 69: Reinstalling Printer SoftwareYou ca
Page 70 and 71: 3 Basic PrintingThis chapter explai
Page 72 and 73: Paper TabUse the following options
Page 74 and 75:
Extras TabYou can select output opt
Page 76 and 77:
4 Advanced PrintingThis chapter exp
Page 78 and 79:
Printing on Both Sides of PaperYou
Page 80 and 81:
Dear ABCRegardsWORLD BESTWORLD BEST
Page 82 and 83:
6 Using Windows PostScriptDriver(Ph
Page 84 and 85:
8 Using Your Printer with aMacintos
Page 86 and 87:
Printer Features SettingThe Printer
Page 88 and 89:
SOFTWARE SECTIONINDEXAadvanced prin
show all

Download - Xerox Support and Drivers

Create successful ePaper yourself

Delete template?

Save as template?