Installation/startup instruction (English) - PNet - Trend

More documents

Recommendations

Info

Configuration Process4.1 Configure the Driver Using a Solution (continued)11. Display a strategy page for the IQ3/XNC, by right-clicking the page, pointing to Device and clicking XNCInterface Module. The XNC Interface Module dialogue box is displayed.12. Configure the driver’s communication settings by double-clicking the string value for each store and enteringthe required value. See the ‘Configure the Driver’s Communications Settings’ section of this manual formore details.13. Configure the device details by double-clicking the string value for each store and entering the required value.See the ‘Configure Device Details’ section of this manual for more details.14. Configure the driver’s output labels to make identification of the outputs easier by double clicking the output’slabel in the Outputs area, entering the new label and clicking OK. See the ‘Configure Input/Output Labels’section of this manual for more details.15. Click OK to close the XNC Interface Module dialogue box.16. Configure the IQ3/XNC’s strategy as required. The solution includes digital input and sensor modules alreadylinked to the XNC interface module’s outputs. If required you can delete modules linked to outputs you are notusing. For details of configuring the strategy of an IQ3/XNC see the SET Manual (TE200147).If you are reading the comms status from the device it needs to be linked into the strategy as required so thatthe required action can be carried out. This is done by linking the connective linked to the TCL output towhich the comms status is written to the appropriate part of the alarm handling strategy.17. Download the strategy. See the ‘Download the Strategy’ section of this manual for more details.4.2 Configure the Driver by Adding an IQ3/XNC to the ProjectWhen a driver is added using a solution (see the ‘Configure the Driver Using a Solution’ section of this manual)the driver is placed in the project directory. This enables it to be manually added to the controller’s TCL Module.To configure the IQ3/XNC MODBUS Driver by adding an IQ3/XNC to the project:1. Install the device(s) which are to be communicated with according to the manufacturer’s installationinformation.2. Install the IQ3/XNC as described in the IQ3xact Web Enabled Controller Installation Instructions (TG200766)or the IQ3xcite Web Enabled Controller Installation Instructions(TG200626), and the IQ3../.../XNC/..Controller/Interface Installation Instructions (TG200911).3. Connect the IQ3/XNC to the MODBUS devices as described in the ‘Connect the IQ3/XNC to the MODBUSDevices’ section of this manual.4. Configure the driver as described in the ‘Configure the IQ3/XNC MODBUS Driver’ section of this manual.5. Configure the IQ3/XNC’s strategy as described in the ‘Configure the IQ3/XNC Strategy’ section of thismanual14 IQ3/XNC MODBUS Driver Manual TE201101 Issue 2, 12-Apr-2011
T T RA RB0VTXRXRTS / TXENCTS / RXEN Connect the IQ3/XNC to the MODBUS Devices5 Connect the IQ3/XNC to the MODBUS DevicesThe connection of the IQ3/XNC to the MODBUS devices can be made using either a serial connection or a TCP/IPconnection. The type of connection used will determine which variant of the driver is used.Note that only one of the IQ3/XNC’s RS232 connectors can be used at a time, and it is not possible to use RS232 andRS485 connectors at the same time.For more details of connection the IQ3/XNC see the ‘IQ3../.../XNC/... Controller/Interface Installation Instructions’(TG200911).5.1 Connect to the MODBUS Devices Using a Serial ConnectionThe connection between the MODBUS and the IQ3/XNC can be made using either the IQ3/XNC’s RS232, or RS485connector. The RS232 connection is a peer to peer connection with only one MODBUS slave and a maximumdistance of 20 m between master and last slave. The RS 485 connection is limited to a maximum of 32 slave maxwith a distance maximum of 1000 m between master and last slave.To connect to the MODBUS devices using a serial connection:1. Install the IQ3/XNC as described in the IQ3xact Web Enabled Controller Installation Instructions (TG200766)or the IQ3xcite Web Enabled Controller Installation Instructions(TG200626), and the IQ3../.../XNC/..Controller/Interface Installation Instructions (TG200911).2. Connect the IQ3/XNC to the MODBUS using its RS232 or RS485 connectors as shown below.RS232 with 9 Way D type connector + 0RS485RS232A B RS232 9 way D type1IQ3/XNC pinouts6RTS7CTS892 RX3TX4 (held high)5 GNDMODBUSDeviceThe pinouts shown are those for the IQ3/XNC. The pins from the IQ3/XNC should be wired to the appropriateterminals on the MODBUS device.IQ3/XNC MODBUS Driver Manual TE201101 Issue 2, 12-Apr-201115
Page 5 and 6: About this Manual1 About this Manua
Page 7: About the IQ3/XNC MODBUS Driver2 Ab
Page 13: Configuration Process4 Configuratio
Page 17 and 18: 0VT T RA RBRTS / TXENCTS / RXENTXRX
Page 19 and 20: Configure the IQ3/XNC MODBUS Driver
Page 33 and 34: Configure the IQ3/XNC Strategy7 Con
Page 35 and 36: Configure the IQ3/XNC Strategy7.3 D
Page 37 and 38: Configuration ExampleAppendicesA1Co
Page 39 and 40: Configuration ExampleA1Configuratio
Page 41 and 42: Configuration ExampleA1Configuratio
Page 43 and 44: Trouble ShootingA2Trouble ShootingT
Page 45 and 46: IndexIndexAAboutIQ3/XNC3 MODBUS Dri
Page 47 and 48: IQ3/XNC MODBUS Driver Manual TE2011

Installation/startup instruction (English) - PNet - Trend

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?