PDF Nimco electronics - Total Hydraulics BV

www.nimco-controls.comElectrical Control Units

ContentsPage 4Page 5Page 6Page 7Page 8Page 9Page 10Page 12Page 13System Options OverviewTechnical DataEPC 100 1-Axis ControllerEPC 300 2-Axis ControllerEPC 700 4-Axis ControllerEPC 350 3-Axis ControllerEDB 64 Driver UnitCC8 Control CardDriver Boxwww.nimco-controls.com3

System Options OverviewEPC 100EPC 300EPC 350EPC 700CC8/BICC8EasyProgEDB 8-64EDB 16-64CV110CV2000 LSCV5504www.nimco-controls.com

EPC 100 1-Axis ControllerThe EPC 100 is a single axis analogue control joystick. Angular operating range is ±20° and theoperating principle is non-contacting rotating magnetic field over hall-sensor. It is short circuit-proof(short circuit duration: unlimited).Type No. Operating Voltage Output Signal Current Consumption Load Resistance Centre PositionEPC 100 A1 10–30 V DC 4–20 mA 12 V -> 18 mA 1) 12 mAEPC 100 A6 4,5–5,5 V DC 0,5–4,5 V DC ratio./propor max. 10 mA > 20 kΩ typ. 2,5 VEPC 100 A7 10–30 V DC 0,5–4,5 V DC 12 V -> 15 mA > 20 kΩ typ. 2,5 V1) with Operating Voltage : 10 V < 250 Ω30 V < 1250 Ωwww.nimco-controls.com5

EPC 300 2-Axis ControllerThe EPC 300 is a two axis analogue control joystick. Angular operating range is ±20° in bothdirections and the operating principle is non-contacting rotating magnetic field over hall-sensor.It is short circuit-proof (short circuit duration: unlimited). It can be fitted wit 1-3 on/off pushbuttons on the top of the grip as an option.proportionaler Bereichproportional areadébattement angulaireMinitaste optionalmini push button optionalbouton poussoir miniature optionnelGriffversion (wahlweise)knob (alternatively)levier (facultativement)Type No. Operating Voltage Output Signal Current Consumption Load Resistance Centre PositionEPC 300 A1 10–30 V DC 4–20 mA 12 V -> 18 mA 1) 12 mAEPC 300 A6 4,5–5,5 V DC 0,5–4,5 V DC ratiom./propor max. 10 mA > 20 kΩ typ. 2,5 VEPC 300 A7 10–30 V DC 0,5–4,5 V DC 12 V -> 15 mA > 20 kΩ typ. 2,5 V1) with operating voltage : 10 V < 250 Ω30 V < 1250 Ω6www.nimco-controls.com

EPC 700 2-Axis ControllerThe EPC 700 is a two axis heavy duty analogue control joystick. Angular operating range is±25° in both directions and the operating principle is non-contacting rotating magnetic fieldover hall-sensor. It is short circuit-proof (short circuit duration: unlimited).Type No. Operating Voltage Output Signal Current Consumption Load Resistance Centre PositionEPC 700 A1 10–30 V DC 4–20 mA max. 10 mA 1) 12 mAEPC 100 A6 4,5–5,5 V DC 0,5–4,5 V DC ratiom./proporMAX 10 mA > 20 kΩ typ. 2,5 VEPC 100 A7 10–30 V DC 0,5–4,5 V DC 12 V -> 15 mA > 20 kΩ typ. 2,5 V1) with operating voltage : 10 V < 250 Ω30 V < 1250 Ωwww.nimco-controls.com7

EPC 350 3-Axis ControllerThe EPC 350 is a three axis analogue control joystick.Angular operating range is ±20° in X- and Y-directionsand ±30° in the Z-axis. The operating principle is noncontactingrotating magnetic field over hall-sensor.DIMENSIONSAbt. 39Abt. 72Abt. 49OUTPUT CHARACTERISTICSCONNECTOR WIRING DIAGRAM8www.nimco-controls.com

EPC 350 3-Axis ControllerMECHANICAL PERFORMANCESMechanical Operating Angle X and Y axes : +/- 20°Z axis : +/- 30°Operating Force X and Y axes : 1-4NZ axis : 40-80 mNmELECTRICAL PERFORMANCESCurrent ConsumptionIndependant Linearity ToleranceSingle Output : Max 33 mADouble Output : Max 66 mA+/- 3% FSElectrical Rotating Angle X and Y axes : +/- 20° (40°)Z axis : +/- 30° (60°)Centre Return Accurancy50% +/- 5%VinApplied Voltage D.C.5V +/- 10%Load ResistanceDielectic Strenght 1 minuteInsulation ResistanceOutput Temperature CharacteristicsDrift at Center PositionOver 10kΩat 500V A.C.Over 1,000MΩ at 500V D.C.Below +/- 2,5% Vout - FSBelow +/- 1% Vout - FSOTHERSOperating Temperature RangeVibrationShockLife ExpectancyLever Strength for X and Y axesStopper Strenght for Z axisIndex of ProtectionEMS ToleranceESD Tolerance-20°-+60° (However, not frozen)10-55Hz, 98m/s²(It applies to MIL-STD-202F-204)294m/s²(It applies to MIL-STD-202F-213)X and Y axes : Approx. 5,000,000 operationsZ axis : Approx. 2,000,000 operations(The life when carrying out per minute 60 round trip operation of the knobwithin a mechanical operation angle is expressed with normal temperature)Max. 300N (This value shows the value of static load to the part of knob)Max.0.5Nm (This value shows the value of static load to the part of knob)IP=65 (This value shows the value from above panel towards knob only)100V/m (80MHz~1GHz with 1KHz 80% Amplitude Modulation)+/- 8kV contact discharge /±15kV air dischargewww.nimco-controls.com9

EDB 8-64 Driver UnitThe EDB 64 8-64 is a PWM I/O module which is hermetically sealedin a solid aluminium capsule to protect it against the hazards ofmobile environments, such as humidity and vibration.The module is programmable through the Windows based NimcoEasyProg software.It can be used to control up to 8 (4+4) proportional solenoids and hasa CAN-bus interface. All PWM outputs have a current feedback tocompensate for varying coil resistance due to heating of the solenoidvalves. It can be programmable for 12 or 24 VDC operation.SpecificationPower SupplyVoltage RippleCAN ProtocolCAN DriverNumber of I/OCPUFlash MemoryOperating Temp.PreselectionsModule IP-classPWM OutputsMaximum LoadCurrent FeedbackRamptimeOvertemp ProtectedResponse TimeShopper frequencyResolutionError Detection10-30 VDC

EDB 16-64 Driver UnitThe EDB 16-64 is an I/O module with 16 (8+8) PWM outputs, 8analogue inputs (0-5 VDC) and one digital output. It has a CANbusinterface enabling it to be programmed and connected toother units.The module is programmable through the Windows based NimcoEasyProg software.It is hermetically sealed in a plastic capsule to protect it againstthe hazards of mobile environments, such as humidity andvibration.SpecificationPower SupplyVoltage RippleCAN ProtocolCAN DriverAnalogue inputsDigital outputsNumber of PWM I/OCPUFlash MemoryOperating Temp.PreselectionsModule IP-classPWM OutputsMaximum LoadCurrent FeedbackRamptimeOvertemp ProtectedResponse TimeShopper frequencyResolutionError detection10-30 VDC

CC8 Control CardThe CC8 Control card is an analogue joystick circuit board that is designed to fit underneath a joystick controller and the smallsize makes it ideal to fit under most joysticks. The CAN bus connection enables it to be programmed and connected to other CANmodules.It has 8 analogue balanced inputs (0-5 VDC) for use together with a 2-axis joystick.It comes in two different versions, either just the circuit board for integration together with a joystick (order code : CC8), or in ahermetically sealed capsule (order code : cc8-BI) as a stand alone unit.SpecificationPower Supply 10-30 VDCVoltage Ripple

CC8 Control CardINSTALLATION DRAWING95733578MaterialSurf. Treatm.RevisionsDrawn bySheet:TF2009-05-27DateCheckedFormat----1 of 1 A4Sign.Approved----Scale1:2TitleAssembly No.Dwg No.--Mode0www.nimco-controls.com13

EasyProgNimco EasyProg is an easy-to-use, intuitive software for programming the different Nimco CANbus modules. The interface is basedon logic programming using boolean operators to define the program instructions. A relay schematic is available as support forthe programmer to get an easy-to-read overview of the program. Basically no programming experience is needed to start buildingprograms in EasyProg.The programs are built in three simple steps, starting by adding and configuring the different modules to be programmed, thenbuilding the program logic by setting the output conditions of each individual module port. It is easy to create subroutines that can bereused throughout the program. When the programming is finished, the program is simply downloaded to the different modules andthe system is ready for use.It is possible to upload the program from any module to make modifications, and also to make real-time analysis of the systemstatus in form of numerical read-outs, bar graphs or histograms. This is highly useful i.e. for trouble shooting purposes or testing newsoftware functionality.EasyProgNimcoEasyProgNimcoProgramming windowModule Configuration WindowEasyProgNimcoEasyProgNimcoAnalyse window – Bar GraphsAnalyse window – Histogram14www.nimco-controls.com

Nimco Controls AB, Agnesfridsvägen 186 - SE 213 75- Malmö - SwedenTel: + 46 40 22 76 00 - Fax: +46 40 22 76 01 - Email: saleseurope@nimco.seNimco Controls Inc., 1500 S. Sylvania Avenue, #101, Sturtevant WI53177, USATel: (262) 884-0950 - Fax: (262) 886-1129 - Email: salesusa@nimco.seNimco Controls (Asia) Ltd, Unit 1206, 7 12/F New victory HouseNO. 93-103 Wing Lok St. Central Hong-Kong