Operating and installation instructions KNX MSE 8M230 - Warema

More documents

Recommendations

Info

RCommissioningAfter the installation has been completed and the supplyvoltage is applied, the device can be operated on a membranekeyboard (Fig. 3).Local operationThe membrane keyboard consists of 4 buttons; the UP/DOWN and PRG buttons have an integrated LED. Thechannel is selected using the SEL (Select) button. The selectedchannel is displayed by one of the 8 channel LEDs.Fig. 3PRGSELMembrane keyboardKNX MSE 8M2301234Upon delivery, all outputs can be operated in dead man'smode (jog mode, when the button is released, the respectiverelay drops out immediately).To select the channel, press the SEL (Select) button repeatedlyuntil the desired channel lights up. When the UPor DOWN button is activated, the relay begins operatingand the associated output is switched accordingly for theduration of the activation.5678MaintenanceThere are no parts within the device that require maintenance.In the event of a malfunction, the built-in miniaturefuses should only be changed by a qualified electrician.LiabilityFailure to comply with the product information in theseinstructions and use of the unit in a manner that contravenesits intended use and purpose may result in themanufacturer refusing to honour warranty claims for productdamage. In this case, liability for consequential harmto persons or damage to property will also be excluded.Follow the instructions in the operating manual of your sunshading system. The automatic or manual operation ofthe sun shading system when iced over as well as usingthe sun shading system during severe weather may causedamage and must be prevented by the user by taking suitableprecautions.DisposalAfter its use, the device must be disposed of according tolegal regulations or returned to your local recycling centre.EIB and KNX are registered trademarks of the KONNEXAssociation.WARNINGNever randomly press the keys on themembrane keyboard without having a lineof sight to the sun shading system.ProgrammingNOTE:Take suitable precautions to prevent damagedue to electrostatic discharge!Press the programming button (Fig. 3) to putthe device into programming mode. The redLED lights up when programming mode isactive. The device is programmed on a PCwith the corresponding software. This softwareends the programming mode automatically.The red LED goes out.If the programming mode is to be endedearlier, press the programming button again.The red LED goes out.2We reserve the right to carry out improvements890578_a•en•26.10.2011
Technical dataKNX MSE 8M230 Min. Typ. Max. UnitOperating voltage 198 230 253 V ACQuiescent current consumption,10 13 18 mAprimaryDegree of protection inIP30DIN rail-mounted housingDegree of protectionI(PE is looped through)Output per driveSwitching capacity500 VAat 230 V AC/cos ϕ = 0.6KNX input TP 1KNX current consumption 9 mAVoltage 29 V DCConformityViewable at www.warema.deAmbient conditionsOperating temperature -5 20 40 °CStorage temperature 0 20 60 °CRel. humidity10 40 85 %RH(non-condensing)ConnectionSupply line, drivesScrewed terminalsKNX bus systemSpring-load terminalsWire cross sectionsSupply line, outputsMax. 2.5 mmKNX bus systemMax. 0.8 mm ∅Test standardsProduct standard:DIN EN60730-1:2005-12 +DIN EN50090-2-2:1997-06EIB/KNX System Conformance TestEMC basic standards: DIN EN61000-6-2:2002-08DIN EN61000-6-3:2005-06DIN EN 50366:2006-11EnclosureDegree of protectionREG housingIP30MiscellaneousAutomatic operation Type 1Software classALocation of useClean ambient conditionsArticle numbersKNX MSE 8M230 REG 1002 710WAREMA Renkhoff SEHans-Wilhelm-Renkhoff Strasse 2D-97828 Marktheidenfeld, GermanyFig. 4106 mm / 6 MW60 mm90 mm95 mmDimensions of DIN rail-mounted housing,6 MW (modular width)890578_a•en•26.10.2011We reserve the right to carry out improvements3
Page 1: Operating and installation instruct

Operating and installation instructions KNX MSE 8M230 - Warema

Create successful ePaper yourself

Delete template?

Save as template?