Christie DHD800 Serial Communications Protocol-Extended

More documents

Recommendations

Info

PDG-DHT8000L Expand Serial Command Functional Specifications9.8.6 CR_VPOS CommandCommand “CR_VPOS” [CR]Details Get setting status of V PositionAcceptable “000_%1” [CR]Response %1 “-15”-”015”Unacceptable “Error Code” [CR]9.8.7 CR_HSCALE CommandCommand “CR_HSCALE” [CR]Details Get setting status of H scaleAcceptable “000_%1” [CR]Response %1 “-32”-”035”Unacceptable “Error Code” [CR]9.8.8 CR_HPOS CommandCommand “CR_HPOS” [CR]Details Get setting status of H PositionAcceptable “000_%1” [CR]Response %1 “-15”-”015”Unacceptable “Error Code” [CR]DHD800 RS232 Codes-Expand Technical Ref.020-000582-01 Rev. 1 (11-2012)77/101
PDG-DHT8000L Expand Serial Command Functional Specifications9.9 Lamp Status Read Commands9.9.1 CR_LAMPREPL CommandCommandDetailsResponse“CR_LAMPREPL” [CR]Get the information of Lamp Replacement timeAcceptable%1Unacceptable“000_%1” [CR]“2**”2 ---------------- indicates 2 lamps are used in this model.* ---------------- indicates the status of each lamp in lamp numberorder.“Y” means the lamp operating time is over thethreshold for lamp replacement, and “N” meansit has not reached to.e.g.“2YN” ------------ This indicates it is 2-lamp system, and Lamp #2has not been reached to the replacement timewhile #1 should be replaced.“?” [CR]9.9.2 CR_LAMPMODE CommandCommandDetailsResponse“CR_LAMPMODE” [CR]Get Lamp mode setting statusAcceptable%1Unacceptable“000_%1” [CR]“FULL” ---------------- Lamp mode is set to 2-lamp (FULL)“LAMP1”-------------- Lamp mode is set to Lamp1“LAMP2” ------------- Lamp mode is set to Lamp2“?” [CR]9.9.3 CR_AUTOLAMPCONTRL CommandCommandDetailsResponse“CR_AUTOLAMPCONTRL” [CR]Get selected Lamp control modeAcceptable%1Unacceptable“000_%1” [CR]“NORMAL” ---------- NORMAL is selected.“ECO1” --------------- ECO1 is selected.“ECO2” --------------- ECO2 is selected.“Error Code” [CR]9.9.4 CR_LAMPSTS CommandCommandDetailsResponse“CR_LAMPSTS” [CR]Get the information of Lamp lighting statusAcceptable%1Unacceptable“000_%1” [CR]“2**”The first character indicates 2 lamps are used in this model.The following characters indicate each lamp status in lampnumber order as showed below.“I” ------------------------ Lamp is ON“O” ---------------------- Lamp is OFF“X” ----------------------- Lamp Failuree.g.“2IO” ------------------- This indicates it is 2-lamps system, Lamp#1 is ON, and #2 is OFF.“?” [CR]DHD800 RS232 Codes-Expand Technical Ref.020-000582-01 Rev. 1 (11-2012)78/101
Page 1 and 2:
DHD800 RS232 Codes-ExpandTechnical
Page 4 and 5:
PDG-DHT8000L Expand Serial Command
Page 6 and 7:
Page 8 and 9:
Page 10 and 11:
Page 12 and 13:
Page 14 and 15:
Page 16 and 17:
Page 18 and 19:
Page 20 and 21:
Page 22 and 23:
Page 24 and 25:
Page 26 and 27:
Page 28 and 29: PDG-DHT8000L Expand Serial Command
Page 102: PDG-DHT8000L Expand Serial Command
show all

Christie DHD800 Serial Communications Protocol-Extended

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?