Christie DHD800 Serial Communications Protocol-Extended
Christie DHD800 Serial Communications Protocol-Extended Christie DHD800 Serial Communications Protocol-Extended
PDG-DHT8000L Expand Serial Command Functional Specifications8.7.6 CF_REAR CommandCommand%1DetailsResponse“CF_REAR_%1” [CR]“ON” --------------------------- Set Rear to ON“OFF” ------------------------- Set Rear to OFFSet/Cancel Rear. (Valid only when in the normal Power ON status.)When Rear is set to ON, image is left/right reversed.The status set by this command is stored in EEPROM and the setting remainseffective after the power is turned to ALL OFF status.AcceptableUnacceptable“000” [CR]“Error Code” [CR]8.7.7 CF_VSCALE CommandCommand%1DetailsResponse“CF_VSCALE_%1” [CR]“035” ---------------------- +35“031” ---------------------- +31:“001” ---------------------- +1“000” ---------------------- ±0“‐01” ---------------------‐1:“‐31” ---------------------‐31“‐32” ---------------------‐32“UP” --------------------- Increment setting value of Vscale by 1“DN” --------------------- Decrement setting value of Vscale by 1Set Vscale (Available only in the normal Power ON status)*When selected screen mode is a setting except Custom, return “101” [CR] andthe command is not executed.* When input is no signal, return “101” [CR] and the command is not executed.AcceptableUnacceptable“000” [CR]“Error Code” [CR]8.7.8 CF_VPOS CommandCommand%1DetailsResponse“CF_VPOS_%1” [CR]“015” --------------------- +15“014” --------------------- +14:“001” --------------------- +1“000” --------------------- ±0“‐01” ---------------------‐1:“‐14” ---------------------‐14“‐15” ---------------------‐15“UP” --------------------- Increment setting value of Vposition by 1“DN” --------------------- Decrement setting value of Vposition by 1Set V Position (Available only in the normal Power ON status)*When selected screen mode is a setting except Custom, return “101” [CR] andthe command is not executed.* When input is no signal, return “101” [CR] and the command is not executed.AcceptableUnacceptable“000” [CR]“Error Code” [CR]DHD800 RS232 Codes-Expand Technical Ref.020-000582-01 Rev. 1 (11-2012)35/101
PDG-DHT8000L Expand Serial Command Functional Specifications8.7.9 CF_HSCALE CommandCommand%1DetailsResponse“CF_HSCALE_%1” [CR]“035” ---------------------- +35“031” ---------------------- +31:“002” ---------------------- +2“001” ---------------------- +1“000” ---------------------- ±0“‐01” ---------------------‐1“‐02” ---------------------‐2:“‐31” ---------------------‐31“‐32” ---------------------‐32“UP” --------------------- Increment setting value of Hscale by 1“DN” --------------------- Decrement setting value of Hscale by 1Set Hscale (Available only in the normal Power ON status)*When selected screen mode is a setting except Custom, return “101” [CR] andthe command is not executed.* When input is no signal, return “101” [CR] and the command is not executed.AcceptableUnacceptable“000” [CR]“Error Code” [CR]8.7.10 CF_HPOS CommandCommand%1DetailsResponse“CF_HPOS_%1” [CR]“015” --------------------- +15“014” --------------------- +14:“002” --------------------- +2“001” --------------------- +1“000” --------------------- ±0“‐01” ---------------------‐1“‐02” ---------------------‐2:“‐14” ---------------------‐14“‐15” ---------------------‐15“UP” --------------------- Increment setting value of Hposition by 1“DN” --------------------- Decrement setting value of Hposition by 1Set H Position (Available only in the normal Power ON status)*When selected screen mode is a setting except Custom, return “101” [CR] andthe command is not executed.* When input is no signal, return “101” [CR] and the command is not executed.AcceptableUnacceptable“000” [CR]“Error Code” [CR]DHD800 RS232 Codes-Expand Technical Ref.020-000582-01 Rev. 1 (11-2012)36/101
- Page 1 and 2: DHD800 RS232 Codes-ExpandTechnical
- Page 4 and 5: PDG-DHT8000L Expand Serial Command
- Page 6 and 7: PDG-DHT8000L Expand Serial Command
- Page 8 and 9: PDG-DHT8000L Expand Serial Command
- Page 10 and 11: PDG-DHT8000L Expand Serial Command
- Page 12 and 13: PDG-DHT8000L Expand Serial Command
- Page 14 and 15: PDG-DHT8000L Expand Serial Command
- Page 16 and 17: PDG-DHT8000L Expand Serial Command
- Page 18 and 19: PDG-DHT8000L Expand Serial Command
- Page 20 and 21: PDG-DHT8000L Expand Serial Command
- Page 22 and 23: PDG-DHT8000L Expand Serial Command
- Page 24 and 25: PDG-DHT8000L Expand Serial Command
- Page 26 and 27: PDG-DHT8000L Expand Serial Command
- Page 28 and 29: PDG-DHT8000L Expand Serial Command
- Page 30 and 31: PDG-DHT8000L Expand Serial Command
- Page 32 and 33: PDG-DHT8000L Expand Serial Command
- Page 34 and 35: PDG-DHT8000L Expand Serial Command
- Page 38 and 39: PDG-DHT8000L Expand Serial Command
- Page 40 and 41: PDG-DHT8000L Expand Serial Command
- Page 42 and 43: PDG-DHT8000L Expand Serial Command
- Page 44 and 45: PDG-DHT8000L Expand Serial Command
- Page 46 and 47: PDG-DHT8000L Expand Serial Command
- Page 48 and 49: PDG-DHT8000L Expand Serial Command
- Page 50 and 51: PDG-DHT8000L Expand Serial Command
- Page 52 and 53: PDG-DHT8000L Expand Serial Command
- Page 54 and 55: PDG-DHT8000L Expand Serial Command
- Page 56 and 57: PDG-DHT8000L Expand Serial Command
- Page 58 and 59: PDG-DHT8000L Expand Serial Command
- Page 60 and 61: PDG-DHT8000L Expand Serial Command
- Page 62 and 63: PDG-DHT8000L Expand Serial Command
- Page 64 and 65: PDG-DHT8000L Expand Serial Command
- Page 66 and 67: PDG-DHT8000L Expand Serial Command
- Page 68 and 69: PDG-DHT8000L Expand Serial Command
- Page 70 and 71: PDG-DHT8000L Expand Serial Command
- Page 72 and 73: PDG-DHT8000L Expand Serial Command
- Page 74 and 75: PDG-DHT8000L Expand Serial Command
- Page 76 and 77: PDG-DHT8000L Expand Serial Command
- Page 78 and 79: PDG-DHT8000L Expand Serial Command
- Page 80 and 81: PDG-DHT8000L Expand Serial Command
- Page 82 and 83: PDG-DHT8000L Expand Serial Command
- Page 84 and 85: PDG-DHT8000L Expand Serial Command
PDG-DHT8000L Expand <strong>Serial</strong> Command Functional Specifications8.7.6 CF_REAR CommandCommand%1DetailsResponse“CF_REAR_%1” [CR]“ON” --------------------------- Set Rear to ON“OFF” ------------------------- Set Rear to OFFSet/Cancel Rear. (Valid only when in the normal Power ON status.)When Rear is set to ON, image is left/right reversed.The status set by this command is stored in EEPROM and the setting remainseffective after the power is turned to ALL OFF status.AcceptableUnacceptable“000” [CR]“Error Code” [CR]8.7.7 CF_VSCALE CommandCommand%1DetailsResponse“CF_VSCALE_%1” [CR]“035” ---------------------- +35“031” ---------------------- +31:“001” ---------------------- +1“000” ---------------------- ±0“‐01” ---------------------‐1:“‐31” ---------------------‐31“‐32” ---------------------‐32“UP” --------------------- Increment setting value of Vscale by 1“DN” --------------------- Decrement setting value of Vscale by 1Set Vscale (Available only in the normal Power ON status)*When selected screen mode is a setting except Custom, return “101” [CR] andthe command is not executed.* When input is no signal, return “101” [CR] and the command is not executed.AcceptableUnacceptable“000” [CR]“Error Code” [CR]8.7.8 CF_VPOS CommandCommand%1DetailsResponse“CF_VPOS_%1” [CR]“015” --------------------- +15“014” --------------------- +14:“001” --------------------- +1“000” --------------------- ±0“‐01” ---------------------‐1:“‐14” ---------------------‐14“‐15” ---------------------‐15“UP” --------------------- Increment setting value of Vposition by 1“DN” --------------------- Decrement setting value of Vposition by 1Set V Position (Available only in the normal Power ON status)*When selected screen mode is a setting except Custom, return “101” [CR] andthe command is not executed.* When input is no signal, return “101” [CR] and the command is not executed.AcceptableUnacceptable“000” [CR]“Error Code” [CR]<strong>DHD800</strong> RS232 Codes-Expand Technical Ref.020-000582-01 Rev. 1 (11-2012)35/101