Christie DHD800 Serial Communications Protocol-Extended

More documents

Recommendations

Info

PDG-DHT8000L Expand Serial Command Functional Specifications8.4.12 CF_GAMMA CommandCommand%1DetailsResponse“CF_GAMMA_%1” [CR]“000-015” ---------------- Directly specify setting value of Gamma“UP”---------------------- Increment setting value of Gamma by 1“DN”---------------------- Decrement setting value of Gamma by 1Set user controlled value of Gamma. (Available only in the normal Power ONstatus)The value set by this command is not stored in the projector’s memory. Therefore,when the power is turned to ALL OFF status, the value returns to the originalsetting. (It is stored in Suspend mode.)AcceptableUnacceptable“000” [CR]“Error Code” [CR]8.4.13 CF_NZRED CommandCommand%1DetailsResponse“CF_NZRED_%1” [CR]“ON” ------------------------------Set Noise Reduction to ON“OFF” ---------------------------- Set Noise Reduction to OFFSet or Cancel Noise Reduction. (Available only in the normal Power ON status)The value set by this command is not stored in the projector’s memory.Therefore, when the power is turned to ALL OFF status, the value returns to theoriginal setting. (It is stored in Suspend mode.)AcceptableUnacceptable“000” [CR]“Error Code” [CR]8.4.14 CF_PROGV CommandCommand%1DetailsResponse“CF_PROGV_%1” [CR]“ON” ------------------------------ Set Progressive scan to ON“FILM” ---------------------------- Set Progressive scan to Film mode“OFF” ---------------------------- Set Progressive scan to OFFSet or Cancel Progressive scan. (Valid only when it is in the normal Power ONstatus.)The value set by this command is not stored in the projector’s memory. Therefore,when the power is turned to ALL OFF status, the value returns to the originalsetting. (It is stored in Suspend mode.)AcceptableUnacceptable“000” [CR]“Error Code” [CR]8.4.15 CF_BCOLOR CommandCommand%1DetailsResponse“CF_BCOLOR_%1” [CR]“ON” ------------------------------ Set BrilliantColor to ON“OFF” ---------------------------- Set BrilliantColor to OFFSet or Cancel BrilliantColor.AcceptableUnacceptable“000” [CR]“Error Code” [CR]DHD800 RS232 Codes-Expand Technical Ref.020-000582-01 Rev. 1 (11-2012)25/101
PDG-DHT8000L Expand Serial Command Functional Specifications8.4.16 CF_IMAGE CommandCommand%1DetailsResponse“CF_IMAGE__%1” [CR]“STAND” ----------- Standard (Image adjustment value is set to factory default)“REAL” ------------- Real (Fixed value to display graphic image with natural tone)“CINEMA” --------- Cinema (Fixed value to focus on tone reproduction for movie)“DYNAMIC”------- Dynamic (Fixed value to enable projection with a sharp,powerful picture tone)“CUSTOM1” ------ Image1 (values adjusted and stored by user)“CUSTOM2” ------ Image2 (values adjusted and stored by user)“CUSTOM3” ------ Image3 (values adjusted and stored by user)“CUSTOM4” ------ Image4 (values adjusted and stored by user)“CUSTOM5” ------ Image5 (values adjusted and stored by user)“CUSTOM6” ------ Image6 (values adjusted and stored by user)“CUSTOM7” ------ Image7 (values adjusted and stored by user)“CUSTOM8” ------ Image8 (values adjusted and stored by user)“CUSTOM9” ------ Image9 (values adjusted and stored by user)“CUSTOM10” -----Image10 (values adjusted and stored by user)Select Image mode. (Valid only when it is in the normal Power ON status.)Parameter “CUSTOM1” to “CUSTOM10” corresponds to “Image1” to “Image10”displayed in projector OSD menu on selecting Image.The value set by this command is stored in EEPROM so that the setting canremain effective even after the power is turned to ALL OFF status.AcceptableUnacceptable“000” [CR]“Error Code” [CR]8.4.17 CF_IMAGEADJ CommandCommand%1DetailsResponse“CF_IMAGEADJ_%1”[CR]“RST”------ Reset adjusted value for the Image“STR1”---- Store current adjusted value to Image 1“STR2”---- Store current adjusted value to Image 2“STR3”---- Store current adjusted value to Image 3“STR4”---- Store current adjusted value to Image 4“STR5”---- Store current adjusted value to Image 5“STR6”---- Store current adjusted value to Image 6“STR7”---- Store current adjusted value to Image 7“STR8”---- Store current adjusted value to Image 8“STR9”---- Store current adjusted value to Image 9“STR10”--- Store current adjusted value to Image 10Reset or Store adjusted value for Image. (Available only in the normal Power ONstatus)“STR1”-”STR10” corresponds to “Image1”-”Image10” displayed in projector OSDmenu on selecting “Store” for adjusted value of Image. The setting value set in“Image1” to “Image10” is stored and can be retrieved when turning on theprojector again after the power is turned to ALL OFF status.AcceptableUnacceptable“000” [CR]“Error Code” [CR]DHD800 RS232 Codes-Expand Technical Ref.020-000582-01 Rev. 1 (11-2012)26/101
Page 1 and 2: DHD800 RS232 Codes-ExpandTechnical
Page 4 and 5: PDG-DHT8000L Expand Serial Command
Page 76 and 77:
PDG-DHT8000L Expand Serial Command
Page 78 and 79:
Page 80 and 81:
Page 82 and 83:
Page 84 and 85:
Page 86 and 87:
Page 88 and 89:
Page 90 and 91:
Page 92 and 93:
Page 94 and 95:
Page 96 and 97:
Page 98 and 99:
Page 100 and 101:
Page 102:
show all

Christie DHD800 Serial Communications Protocol-Extended

Create successful ePaper yourself

Delete template?

Save as template?