Owner's Manual 2011 CR/WR/XC 125/150 - Husqvarna

More documents

Recommendations

Info

2 - Check that the chain is neither worn out nor damaged. If therollers or the links are damaged, replace the chain by followingthe instructions given in the Periodical MaintenanceTable.3 - Check that neither the sprocket nor the crown are damaged.4 - Wash and clean the chain as described hereunder.Washing the chain without OR (CR)Wash using either oil or diesel oil. When using gasoline or tricloroetilene,clean and lubricate the chain to prevent oxidation.Washing the chain with OR (WR)Wash using oil, diesel oil, or paraffin oil. Never use gasoline,tricloroetilene, or solvents, as the OR may suffer damages.Use instead special sprays for chains with OR.5 - If the chain has been cut, reassemble using a joint.6 - Assemble the joint spring (a) by turning the closed side to thechain direction of rotation as shown in figure below.NOTE*: Even if all the joints are reusable when in good conditions,for safety purposes we advise using new joints whenreassembling the chain.7 - Accurately adjust the chain as described on page 33.WARNING: The chain oil has NEVER to get incontact with the tires or the rear brake disk.Chain tension rollers, chain driving roller,chain guide, chain runnerCheck the wear of the above mentioned elements and replacethem when necessary.WARNING*: Check the chain guide alignement,and remember that a bent elementcan cause a rapid wear of the chain. In thiscase, a chain fleeting from the sprocket mayensue.ENLubricating the chain without OR (CR)First dry, then plunge the chain in a bisulphide molybdenumlubricant, or in high viscosity engine oil. Warm up the oil beforeuse.Note * : As an alternative, you can use suitable spray lubricants.4Lubricating the chain with OR (WR)Lubricate all metallic and rubber (OR) elements using a brush,and use engine oil with SAE 80-90 viscosity for the internal andexternal parts.Note * : As an alternative, you can use suitable spray lubricants.1- Chain tension roller2- Chain driving roller3- Chain guide4- Chain slidera- Joint spring1a2335
Removing the front wheelSet a stand or a block under the engine and see that the frontwheel is lifted from the ground. Loosen the bolts (1) holdingthe wheel axle (2) to the frontfork stanchions.Hold the head of the wheel axle (2) in place, unscrew the bolt(3) on the opposite side; draw the wheel axle out.NOTESDo not operate the front brake lever when the wheel has beenremoved; this causes the caliper piston to move outwards. Afterremoval, lay down the wheel with brake disc on top.211336
Page 2 and 3: ENGLISH1
Page 4 and 5: IMPORTANTThe reference for recognit
Page 6 and 7: IDENTIFICATION DATAThe engine numbe
Page 8 and 9: TECHNICAL DATAENGINEType...........
Page 10 and 11: FUEL COCKCONTROLSThe cock (1) set o
Page 12: DIGITAL INSTRUMENT, WARNING LIGHTS
Page 15 and 16: HANDLEBAR COMMUTATOR (WR)The left c
Page 17 and 18: RIDINGBEFORE EVERY RIDE MAKE FOLLOW
Page 19 and 20: STOPPING THE MOTORCYCLE AND THE ENG
Page 21 and 22: REPLACEMENT OF COOLING FLUIDThe coo
Page 23 and 24: CLUTCH ADJUSTMENTThe clutch is adju
Page 25 and 26: AIR FILTER CHECKTurn rear pin (1) c
Page 27 and 28: ADJUSTMENT OF THE CONTROL LEVER AND
Page 29 and 30: ADJUSTING THE SUSPENSIONS ACCORDING
Page 31 and 32: HANDLEBAR POSITION AND HEIGHT CHANG
Page 33 and 34: 2. Clean ringnut (1) and adjusting
Page 35: CHECKING THE WEAR OF CHAIN, PINION
Page 39 and 40: Removing the rear wheelUnscrew the
Page 41 and 42: BRAKE PADS REMOVAL- Remove springs
Page 43 and 44: BRAKE DISC WEARMeasure the thicknes
Page 45 and 46: ELECTRICAL COMPONENTS LOCATIONThe i
Page 47 and 48: REPLACING THE NUMBER PLATE LAMP (WR
Page 49 and 50: CLEANINGIMPORTANT RECOMMENDATIONPre
Page 51 and 52: Comando acceleratoreComando acceler
Page 54: APPENDICE AAPPENDIX AAPPENDICE AANH
Page 58: A5A
Page 62 and 63: A9A
Page 64 and 65: A11A
Page 82 and 83: MEMORANDUMAA29

Owner's Manual 2011 CR/WR/XC 125/150 - Husqvarna

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?