Owner's Manual 2011 CR/WR/XC 125/150 - Husqvarna

More documents

Recommendations

Info

GEAR SHIFT CONTROLThe lever (1) is placed on the left-hand side of the engine. Theoperator must release the lever after each gear change to allowit to return to its central position before another gear changecan be made.Neutral position (N) is between first (low) and second gears.First gear is engaged by pushing the lever downwards; all theother gears are engaged, by pushing the lever upwards.The position of the gear shift lever on the shaft can be varied by:loosening screw; pulling lever out; placing lever in new positionon the shaft when the operation is over tighten the screw andthen tightening the screw.CAUTION*: Do not shift gears without disengagingthe clutch and closing the throttle. Theengine could be damaged by “overspeed”and shock.WARNING*: Do not downshift when travelingat a speed that would force the engine tooverrev in the next lower gear, or cause therear wheel to lose traction.KICKSTART PEDALThe kickstart pedal (2) is situated on the right-hand side of themotorcycle.ENN: Neutral1215
RIDINGBEFORE EVERY RIDE MAKE FOLLOWING CHECKSWARNING!Before each ride, to prevent accidents or failures during ride,make sure to go through following list.1. Check all fluidsA. Transmission oil levelB. fuel levelC. coolant levelMake sure all caps are properly adjusted.WARNING*: Don’t remove radiator cap whenhot!2. Check all controlsA. Throttle handgripB. Clutch leverMake sure cables are not damaged and turn smoothly.3. Check brakesLook for brake fluid leaks and worn hoses. Check for properfunctioning.4. Check suspensionsCompress fork and rear suspensions. Look for oil leaks andensure proper functioning.5. Check wheelsCheck spokes and look for worn bearings.Check rims and tyres.Check tyre pressure.6. Check chain rollers and sprocketsCheck wear on chain rollers and sprocketsEnsure chain is correctly adjusted and lubricated.7. Check air filter and intake systemCheck that air filter is cleanCheck all rubber connections and clamps.8. Check exhaust systemCheck hook up, look for cracksCheck muffler.9. Check torqueA. Spark plug (see page 23).B. General check of torque10. Check steering actionCheck bearing play.11. Check the electric system (<strong>WR</strong>).Start the engine and check that the front and rear lamps, thestop light, the turn signals the cluster warning lights and thehorn are working correctly.WARNING*: Failure to perform these checksevery day before you ride may result in serousdamage or a severe accident.RUNNING INTo obtain the best settling of the engine moving elements, fordriving your motorcycle to the best of your capability, run in theengine for several hours, following these procedures:1. FROM STOP POSITION. Start the engine and run at idle, butopen the throttle periodically and briefly until the engine is thoroughlywarmed up. Within 3-4 minutes the coolant temperaturewill have reached approximately 60° C/140° F. (Do not ridethe motorcycle).2. Stop the engine, and let it cool down naturally until its temperatureis equal to the ambient air temperature. This will allowthe piston to align itself to any imperfections which might existat the cylinder wall.3. Repeat steps 1 and 2. (Do not ride the motorcycle).4. Bring the engine up to normal running temperature. Ride themotorcycle approximately 10 minutes at moderate speeds. Thenrepeat cool down procedure.AVOID HARD ACCELERATIONS.5. Bring engine up to normal temperature. Ride motorcycleapproximately 15 minutes at moderate to high speeds. Againavoid hard accelerations.6.Repeat cool down procedure.7. Full throttle operation must be avoided until the engine hasreached operating temperature, even after the break in processis completed. When the above procedure is followed correctly,engine durability and performance will be greatly enhanced.CHECKS WHILE RUNNING INWhen running in, the following should be checked out:- WHEELS SPOKES TENSION;- TIGHTENING OF WHEELS;- FORK PIN TIGHTENING;- CHAIN ADJUSTMENT;- STEERING BEARING PLAY;- HANDLEBAR TIGHTENING;- ENGINE GRIP TO FRAME;- SUCTION FITTING GRIP;- HEAD AND CYLINDER NUTS GRIP.Note*:After break in, install a new spark plug andchange the transmission oil.After running-in, check that vehicle nuts andbolts are properly tightened.16
Page 2 and 3: ENGLISH1
Page 4 and 5: IMPORTANTThe reference for recognit
Page 6 and 7: IDENTIFICATION DATAThe engine numbe
Page 8 and 9: TECHNICAL DATAENGINEType...........
Page 10 and 11: FUEL COCKCONTROLSThe cock (1) set o
Page 12: DIGITAL INSTRUMENT, WARNING LIGHTS
Page 15: HANDLEBAR COMMUTATOR (WR)The left c
Page 19 and 20: STOPPING THE MOTORCYCLE AND THE ENG
Page 21 and 22: REPLACEMENT OF COOLING FLUIDThe coo
Page 23 and 24: CLUTCH ADJUSTMENTThe clutch is adju
Page 25 and 26: AIR FILTER CHECKTurn rear pin (1) c
Page 27 and 28: ADJUSTMENT OF THE CONTROL LEVER AND
Page 29 and 30: ADJUSTING THE SUSPENSIONS ACCORDING
Page 31 and 32: HANDLEBAR POSITION AND HEIGHT CHANG
Page 33 and 34: 2. Clean ringnut (1) and adjusting
Page 35 and 36: CHECKING THE WEAR OF CHAIN, PINION
Page 37 and 38: Removing the front wheelSet a stand
Page 39 and 40: Removing the rear wheelUnscrew the
Page 41 and 42: BRAKE PADS REMOVAL- Remove springs
Page 43 and 44: BRAKE DISC WEARMeasure the thicknes
Page 45 and 46: ELECTRICAL COMPONENTS LOCATIONThe i
Page 47 and 48: REPLACING THE NUMBER PLATE LAMP (WR
Page 49 and 50: CLEANINGIMPORTANT RECOMMENDATIONPre
Page 51 and 52: Comando acceleratoreComando acceler
Page 54: APPENDICE AAPPENDIX AAPPENDICE AANH
Page 58: A5A
Page 62 and 63: A9A
Page 64 and 65: A11A
Page 66 and 67:
A13A
Page 68 and 69:
A15A
Page 70 and 71:
A17A
Page 72 and 73:
A19A
Page 74 and 75:
A21A
Page 76 and 77:
A23A
Page 78 and 79:
A25A
Page 80 and 81:
A27A
Page 82 and 83:
MEMORANDUMAA29
show all

Owner's Manual 2011 CR/WR/XC 125/150 - Husqvarna

Create successful ePaper yourself

Delete template?

Save as template?