VEGAPULS WL 61 - 4 ⦠20 mA/HART - two-wire
VEGAPULS WL 61 - 4 ⦠20 mA/HART - two-wire VEGAPULS WL 61 - 4 ⦠20 mA/HART - two-wire
9 Diagnosis, Asset Management and serviceCodeText messageF261Error in theconfigurationF264Installation/Setup errorF265Measurementfunction disturbedCause– Error during setup– False signal suppressionfaulty– Error when carrying out areset– Adjustment not within thevessel height/measuringrange– Max. measuring range ofthe instrument not sufficient– Sensor no longer carriesout a measurement– Operating voltage too lowRectification– Repeat setup– Repeat reset– Check or correct installationand/or parameter adjustment– Use an instrument with biggermeasuring range– Check operating voltage– Carry out a reset– Separate operating voltagebrieflyFunction checkThe following table shows the error codes and text messages in thestatus message "Function check" and provides information on causesas well as corrective measures.CodeText messageC700Simulation activeCause– A simulation is activeRectification– Finish simulation– Wait for the automatic endafter 60 mins.Out of specificationThe following table shows the error codes and text messages in thestatus message "Out of specification" and provides information oncauses as well as corrective measures.Maintenance36S600CodeText messageUnpermissibleelectronicstemperatureS601OverfillingCause– Temperature of the electronicsin the non-specifiedsection– Danger of vessel overfillingRectification– Check ambient temperature– Isolate electronics– Use instrument with highertemperature range– Make sure that there is nofurther filling– Check level in the vesselThe following table shows the error codes and text messages in thestatus message "Maintenance" and provides information on causesas well as corrective measures.VEGAPULS WL 61 • 4 … 20 mA/HART - two-wire38061-EN-121011
9 Diagnosis, Asset Management and serviceCodeText messageM500Error with thereset deliverystatusM501Error in thenon-activelinearizationtableM502Error in thediagnosismemoryM503Reliability toolowM504Error on andevice interfaceM505No echo availableCause– With the reset to deliverystatus, the data could notbe restored– Hardware error EEPROM– Hardware error EEPROM– The echot/noise ratio is thesmall for a reliable measurement– Hardware defect– Level echo can no longerbe detectedRectification– Repeat reset– Load XML file with sensordata into the sensor– Exchanging the electronics– Send instrument for repair– Exchanging the electronics– Send instrument for repair– Check installation andprocess conditions– Clean the antenna– Change polarisation direction– Use instrument with highersensitivity– Check connections– Exchanging the electronics– Send instrument for repair– Clean the antenna– Use a more suitableantenna/sensor– Remove possible falseechoes– Optimize sensor positionand orientationReaction when malfunctionsoccur9.4 Rectify faultsThe operator of the system is responsible for taking suitable measuresto rectify faults.38061-EN-121011Procedure for fault rectificationCheck the 4 … 20 mAsignalVEGAPULS WL 61 • 4 … 20 mA/HART - two-wireThe first measures are:• Evaluation of fault messages, for example via the indicating andadjustment module• Checking the output signal with 4 … 20 mA instruments• Treatment of measurement errorsFurther comprehensive diagnostics options offer a PC with the softwarePACTware and the suitable DTM. In many cases, the reasonscan be determined in this way and faults can be rectified.Connect a handmultimeter in the suitable measuring range accordingto the wiring plan. The following table describes possible errors in thecurrent signal and helps to remove them:37
- Page 1 and 2: Operating InstructionsRadar sensor
- Page 3 and 4: Quick start0,5 m(19.68")100%25 m(19
- Page 5 and 6: Contents10 Dismounting10.1 Dismount
- Page 7 and 8: 2 For your safety2 For your safety2
- Page 9 and 10: 2 For your safetytection. The envir
- Page 11 and 12: 3 Product descriptionScope of deliv
- Page 13 and 14: 4 Mounting4 MountingSuitability for
- Page 15 and 16: 4 Mounting> 200 mm(7.87")Fig. 8: Ve
- Page 17 and 18: 4 MountingFig. 12: Rotation in the
- Page 19 and 20: 4 MountingFig. 16: Mounting of the
- Page 21 and 22: 4 MountingFoam generationFlow measu
- Page 23 and 24: 5 Connecting to power supply5 Conne
- Page 25 and 26: 6 Set up with VEGADIS 626 Set up wi
- Page 27 and 28: 6 Set up with VEGADIS 62Information
- Page 29 and 30: TWISTUSB7 Setup with PACTwareVia in
- Page 31 and 32: 7 Setup with PACTwareIf these value
- Page 33 and 34: 9 Diagnosis, Asset Management and s
- Page 35: 9 Diagnosis, Asset Management and s
- Page 39 and 40: 9 Diagnosis, Asset Management and s
- Page 41 and 42: 9 Diagnosis, Asset Management and s
- Page 43 and 44: 10 Dismounting10 Dismounting10.1 Di
- Page 45 and 46: 11 Supplement3142Fig. 44: Data of t
- Page 47 and 48: 11 SupplementTracking speed of the
- Page 49 and 50: 11.2 Radio astronomy stations11 Sup
- Page 51 and 52: 11 SupplementVEGAPULS WL 61, versio
- Page 53 and 54: 11 SupplementVEGAPULS WL 61, versio
- Page 55 and 56: 11 Supplement11.4 Industrial proper
- Page 57 and 58: Notes38061-EN-121011VEGAPULS WL 61
- Page 59 and 60: Notes38061-EN-121011VEGAPULS WL 61
9 Diagnosis, Asset Management and serviceCodeText messageM500Error with thereset deliverystatusM501Error in thenon-activelinearizationtableM502Error in thediagnosismemoryM503Reliability toolowM504Error on andevice interfaceM505No echo availableCause– With the reset to deliverystatus, the data could notbe restored– Hardware error EEPROM– Hardware error EEPROM– The echot/noise ratio is thesmall for a reliable measurement– Hardware defect– Level echo can no longerbe detectedRectification– Repeat reset– Load XML file with sensordata into the sensor– Exchanging the electronics– Send instrument for repair– Exchanging the electronics– Send instrument for repair– Check installation andprocess conditions– Clean the antenna– Change polarisation direction– Use instrument with highersensitivity– Check connections– Exchanging the electronics– Send instrument for repair– Clean the antenna– Use a more suitableantenna/sensor– Remove possible falseechoes– Optimize sensor positionand orientationReaction when malfunctionsoccur9.4 Rectify faultsThe operator of the system is responsible for taking suitable measuresto rectify faults.380<strong>61</strong>-EN-121011Procedure for fault rectificationCheck the 4 … <strong>20</strong> <strong>mA</strong>signal<strong>VEGAPULS</strong> <strong>WL</strong> <strong>61</strong> • 4 … <strong>20</strong> <strong>mA</strong>/<strong>HART</strong> - <strong>two</strong>-<strong>wire</strong>The first measures are:• Evaluation of fault messages, for example via the indicating andadjustment module• Checking the output signal with 4 … <strong>20</strong> <strong>mA</strong> instruments• Treatment of measurement errorsFurther comprehensive diagnostics options offer a PC with the softwarePACTware and the suitable DTM. In many cases, the reasonscan be determined in this way and faults can be rectified.Connect a handmultimeter in the suitable measuring range accordingto the wiring plan. The following table describes possible errors in thecurrent signal and helps to remove them:37