VEGAPULS WL 61 - 4 ⦠20 mA/HART - two-wire
VEGAPULS WL 61 - 4 ⦠20 mA/HART - two-wire VEGAPULS WL 61 - 4 ⦠20 mA/HART - two-wire
5 Connecting to power supply• Internal check of the electronics••value" on the display or PC•Indication of the instrument type, hardware and software version,measurement loop name on the display or PCIndication of the status message "F 105 Determine measuredThe output signal jumps to the set error currentAs soon as a plausible measured value is found, the correspondingcurrent is outputted to the signal cable. The value corresponds to theactual level as well as the settings already carried out, e.g. factorysetting.24VEGAPULS WL 61 • 4 … 20 mA/HART - two-wire38061-EN-121011
6 Set up with VEGADIS 626 Set up with VEGADIS 626.1 ConnectionThe VEGADIS 62 is an indicating and adjustment unit without externalenergy for looping into 4 … 20 mA/HART circuits.The parameter adjustment of the sensor is carried out via HART communication.During the parameter adjustment, the VEGADIS 62 actsas a Secondary Master with respect to the sensor.23=~41Fig. 24: Connection of VEGADIS 62 to the sensor1 Sensor2 VEGADIS 623 HART resistance > 150 Ω (necessary with low impedance power supply)4 Voltage supply/ProcessingThe following adjustment volume of the connected HART sensor isavailable:Min./Max. adjustment• zero/span adjustment (live adjustment)• Damping6.2 Adjust the sensorProceed as follows for the min./max. adjustment of the sensor:1. Press "OK" to reach the adjustment menu.2. Select the submenu "Measurement" and confirm with "OK".3. Move to the menu item "Unit". There the instrument unit of thesensor is displayed, for example "m".38061-EN-121011VEGAPULS WL 61 • 4 … 20 mA/HART - two-wire4. Move to the menu item "MB begin", there the max. measuringdistance is displayed, for example the default setting 15 m.25
- Page 1 and 2: Operating InstructionsRadar sensor
- Page 3 and 4: Quick start0,5 m(19.68")100%25 m(19
- Page 5 and 6: Contents10 Dismounting10.1 Dismount
- Page 7 and 8: 2 For your safety2 For your safety2
- Page 9 and 10: 2 For your safetytection. The envir
- Page 11 and 12: 3 Product descriptionScope of deliv
- Page 13 and 14: 4 Mounting4 MountingSuitability for
- Page 15 and 16: 4 Mounting> 200 mm(7.87")Fig. 8: Ve
- Page 17 and 18: 4 MountingFig. 12: Rotation in the
- Page 19 and 20: 4 MountingFig. 16: Mounting of the
- Page 21 and 22: 4 MountingFoam generationFlow measu
- Page 23: 5 Connecting to power supply5 Conne
- Page 27 and 28: 6 Set up with VEGADIS 62Information
- Page 29 and 30: TWISTUSB7 Setup with PACTwareVia in
- Page 31 and 32: 7 Setup with PACTwareIf these value
- Page 33 and 34: 9 Diagnosis, Asset Management and s
- Page 35 and 36: 9 Diagnosis, Asset Management and s
- Page 37 and 38: 9 Diagnosis, Asset Management and s
- Page 39 and 40: 9 Diagnosis, Asset Management and s
- Page 41 and 42: 9 Diagnosis, Asset Management and s
- Page 43 and 44: 10 Dismounting10 Dismounting10.1 Di
- Page 45 and 46: 11 Supplement3142Fig. 44: Data of t
- Page 47 and 48: 11 SupplementTracking speed of the
- Page 49 and 50: 11.2 Radio astronomy stations11 Sup
- Page 51 and 52: 11 SupplementVEGAPULS WL 61, versio
- Page 53 and 54: 11 SupplementVEGAPULS WL 61, versio
- Page 55 and 56: 11 Supplement11.4 Industrial proper
- Page 57 and 58: Notes38061-EN-121011VEGAPULS WL 61
- Page 59 and 60: Notes38061-EN-121011VEGAPULS WL 61
5 Connecting to power supply• Internal check of the electronics••value" on the display or PC•Indication of the instrument type, hardware and software version,measurement loop name on the display or PCIndication of the status message "F 105 Determine measuredThe output signal jumps to the set error currentAs soon as a plausible measured value is found, the correspondingcurrent is outputted to the signal cable. The value corresponds to theactual level as well as the settings already carried out, e.g. factorysetting.24<strong>VEGAPULS</strong> <strong>WL</strong> <strong>61</strong> • 4 … <strong>20</strong> <strong>mA</strong>/<strong>HART</strong> - <strong>two</strong>-<strong>wire</strong>380<strong>61</strong>-EN-121011