Operation Manual - Home Mega Global Solution
Operation Manual - Home Mega Global Solution Operation Manual - Home Mega Global Solution
INTRODUCTIONThe DSE 607 Module, has been designed to allow the OEM to meet most of the industry’s complexspecifications. It has been primarily designed to allow the user to start and stop the generator,transfer the load to the generator either manually or automatically. The user also has facility to viewall the system operating parameters via the LCD display.Once started the DSE 607 module monitors the engine, indicating the operational status and faultconditions; automatically shutting down the engine and giving a true first up fault condition of anengine failure by a flashing LED and other simultaneous faults by a steady LED. This information isalso indicated by the LCD display on the front panel.Selective operational sequences, timers and alarm trips can be altered by the customer via either thefront panel controls of via a PC.Access to critical operational sequences and timers for use by qualified engineers, are barred by asecurity code.The module is housed in a robust metal case for the front panel mounting. Connections to the moduleare via locking plug and sockets.CLARIFICATION OF NOTATION USED WITHIN THIS PUBLICATION.NOTE:CAUTION!:WARNING!:Highlights an essential element of a procedure to ensurecorrectness.Indicates a procedure or practice which, if not strictly observed,could result in damage or destruction of equipment.Indicates a procedure or practice which could result in injury topersonnel or loss of life if not followed correctly.ªDeep Sea Electronics Plc owns the copyright to this manual, whichcannot be copied, reproduced or disclosed to a third party withoutprior written permission.4607 OPERATING MANUAL ISSUE 1 11/27/00 MR
1. OPERATION1.1 CONTROLControl of the DSE 607 module is via a series of push-buttons mounted on the front of the modulewith STOP/RESET, MANUAL, START, AUTO, TEST and ALARM MUTE functions. For normaloperation these are the only controls which need to be used. Should further information such asengine parameters be needed then this can be obtained from the smaller LCD control pushbuttons asdetailed later in this document.FIG 11.2 NORMAL MANUAL OPERATIONTo initiate a start sequence press the MANUAL push-button. The LCD display will indicate‘MANUAL CONTROL’.Then, press and hold the START push-button, once the module has commenced the start sequencethe button may then be released.If the pre-heat output option is selected this timer is then initiated, and the auxiliary output selectedis energised.After the pre-heat timer has expired the module will de-energise the pre-heat output and commenceengine starting; the following sequence occurs. The Fuel Solenoid is energised, then the StarterMotor is engaged.607 OPERATING MANUAL ISSUE 1 11/27/00 MR 5
- Page 1 and 2: Deep Sea Electronics PlcMODEL 607OP
- Page 3: 9. TYPICAL WIRING DIAGRAM..........
- Page 7 and 8: NOTE:- Should a ‘Fail to start’
- Page 9 and 10: BATTERY HIGH VOLTAGE, if the module
- Page 11 and 12: 2.3 ELECTRICAL TRIPSElectrical trip
- Page 13 and 14: NOTE:- If the following screen is d
- Page 15 and 16: OPENThis LED indicates that the gen
- Page 17 and 18: Pressing : (WHITE)Would show:-LOW O
- Page 19 and 20: 4.4 FRONT PANEL LAYOUT4.5 REAR PANE
- Page 21 and 22: PIN DESCRIPTION CABLENOTESNoSIZE*31
- Page 23 and 24: PLUG “F” 10 WAYPIN DESCRIPTION
- Page 25 and 26: PLUG “C” 12 WAYPIN DESCRIPTIONN
- Page 27 and 28: PLUG “F” 10 WAYPIN DESCRIPTIONN
- Page 29 and 30: 7. COMMISSIONINGPRE-COMMISSIONINGBe
- Page 31 and 32: 9. TYPICAL WIRING DIAGRAMF F FP1S1P
INTRODUCTIONThe DSE 607 Module, has been designed to allow the OEM to meet most of the industry’s complexspecifications. It has been primarily designed to allow the user to start and stop the generator,transfer the load to the generator either manually or automatically. The user also has facility to viewall the system operating parameters via the LCD display.Once started the DSE 607 module monitors the engine, indicating the operational status and faultconditions; automatically shutting down the engine and giving a true first up fault condition of anengine failure by a flashing LED and other simultaneous faults by a steady LED. This information isalso indicated by the LCD display on the front panel.Selective operational sequences, timers and alarm trips can be altered by the customer via either thefront panel controls of via a PC.Access to critical operational sequences and timers for use by qualified engineers, are barred by asecurity code.The module is housed in a robust metal case for the front panel mounting. Connections to the moduleare via locking plug and sockets.CLARIFICATION OF NOTATION USED WITHIN THIS PUBLICATION.NOTE:CAUTION!:WARNING!:Highlights an essential element of a procedure to ensurecorrectness.Indicates a procedure or practice which, if not strictly observed,could result in damage or destruction of equipment.Indicates a procedure or practice which could result in injury topersonnel or loss of life if not followed correctly.ªDeep Sea Electronics Plc owns the copyright to this manual, whichcannot be copied, reproduced or disclosed to a third party withoutprior written permission.4607 OPERATING MANUAL ISSUE 1 11/27/00 MR
Change language