INDUSTRIAL CHOICE ALKYD ENAMEL PRIMER - Rust-Oleum

TECHNICAL DATAALKYDIC-11INDUSTRIAL CHOICEALKYD ENAMEL PRIMERDESCRIPTIONAPPLICATION (continued)A general purpose modified alkyd primer designed for interior andexterior surfaces.Use on clean, abrasive blasted, or lightly rusted steel in mild tomoderate industrial environments. Not for use on galvanized steel.Wear a NIOSH-approved respirator to control lead exposure. Carefullyclean up with a wet mop or HEPA vacuum. Before you start, find outhow to protect yourself and your family by contacting the U.S.EPA/Lead Information Hotline at 1-800-424-LEAD or log on towww.epa.gov/lead.PRODUCT1-Gallon 5-Gallon Description206282 --- Gray PrimerAPPLICATIONApply only when air and surface temperatures are between 32°–100° F (0°– 38° C) and surface is at least 5° F (3° C) above thedew point.COMPANION PRODUCTSRECOMMENDED TOPCOATIndustrial Choice Alkyd EnamelsPRODUCT APPLICATIONSURFACE PREPARATIONALL SURFACES: Remove all dirt, grease, oil, salt and chemicalcontaminants by washing the surface with Pure Strength ®Cleaner/Degreaser item # 3599402, commercial detergent or othersuitable cleaner. Mold and mildew areas must be cleaned with achlorinated cleaner or bleach solution. Rinse thoroughly with freshwater and allow to fully dry. All surfaces must be dry at time ofapplication.STEEL: Hand tool (SSPC-SP-2) or power tool (SSPC-SP-3) clean toremove all loose rust, mill scale, and deteriorated previous coatings.Abrasive blasting to a minimum Commercial Grade (SSPC-SP-6,NACE 3) with a 1-2 mil (25-50m) surface profile is recommended foroptimal performance. Abrasive blast clean steel requires two coatsof primer.PREVIOUSLY COATED: Previously coated surfaces must be sound andin good condition. Smooth, hard, or glossy finishes should bescarified by sanding to create a surface profile. Industrial Choice Alkyd Enamel Primer is compatible with most coatings, but a testpatch is suggested. WARNING! If you scrape, sand or remove oldpaint from any surface, you may release lead paint dust. LEAD ISTOXIC. EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS ILLNESS,SUCH AS BRAIN DAMAGE, ESPECIALLY IN CHILDREN. PREGNANTWOMEN SHOULD ALSO AVOID EXPOSURE. PRODUCTEQUIPMENT RECOMMENDATIONSBRUSH: Use a good quality natural or synthetic bristle brush.ROLLER: Use a good quality natural or synthetic cover. Use a shortnap roller for smooth surfaces, and a medium nap roller for roughsurfaces.AIR-ATOMIZED SPRAYMethod Fluid Tip Fluid Delivery Atomizing PressurePressure 0.055 –.070 16 oz/min 25–60 psiSiphon 0.055 –.070 – 25–60 psiHVLP (various) 0.043 –.070 8–14 oz/min 10 psi at tipAIRLESS SPRAYTHINNINGFluid Pressure Fluid Tip Filter Mesh1600–2400 psi 0.013–.017 100BRUSH/ROLLER: Normally not required.AIR-ATOMIZED SPRAY: 240402 Thinner – Use up to 15% by volume.AIRLESS SPRAY: 240402 Thinner – Normally not required. If neededuse up to 5% by volume.CLEAN-UP240402 Thinner or Mineral spirits.1 of 4Form: 206721Rev. 4/03Printed in USA

TECHNICAL DATAINDUSTRIAL CHOICE ALKYD ENAMEL PRIMERPerformance characteristicsSystem TestedPrimer: Industrial Choice Alkyd Enamel PrimerTopcoat: N/APENCIL HARDNESSMETHOD: ASTM D3363RESULT: 3HCONICAL FLEXIBILITYMETHOD: ASTM D522RESULT: >33%CYCLIC PROHESION Rating 1-10 10=bestMETHOD: ASTM D5894, 3 cycles, 1008 hoursRESULT: 10 per ASTM D714 for blisteringRESULT: 9 per ASTM D610 for rustingIMPACT RESISTANCE directMETHOD: ASTM D2794RESULT: 120 in - lbsTABER ABRASIONMETHOD: ASTM D4060, CS-17 Wheels, 500 gram load, 1000 cyclesRESULT: 93 mg lossFor chemical and corrosion resistance, see theRust-Oleum Industrial Brands Catalog (Form #206275).2 of 4Form: 206721Rev. 4/03Printed in USA

TECHNICAL DATAINDUSTRIAL CHOICE ALKYD ENAMEL PRIMERPHYSICAL PROPERTIESResin TypePigment TypeSolventsVolatile Organic Compounds206282 GRAY PRIMEROil Modified AlkydCalcium BorosilicateAliphatic Hydrocarbons450 g/L (3.75 lbs./gal.)Weight Per GallonSolidsPer GallonPer LiterBy Weight10.7 lbs.1.3 Kg65.6%By VolumeRecommended Dry Film Thickness(DFT) Per CoatWet Film to Achieve DFT(unthinned material)Theoretical Coverage at1 mil DFT (25 µ)Practical Coverage at RecommendedDFT (assumes 15% material loss)43.7%1.0–2.0 mils (25.0–50.0 µ)2.5 –4.5 mils (62.5–112.5 µ)700 sq. ft./gal. (17.2 m 2 /L)300–600 sq. ft./gal. (7.3–14.6 m 2 /L)Dry Times at 70º–80º F (21º– 27º C)and 50% RelativeHumidityDry Heat ResistanceShelf LifeTack-freeHandleRecoat1/2 –1 hour1–2 hours16–24 hours212º F (100º C)5 yearsSpecification and PerformanceAlternativesUSDA acceptableSafety InformationFlash PointContainsWarning!104º F (40º C)Lead-freeCOMBUSTIBLE LIQUID AND VAPOR. HARMFUL IF INHALED.MAY AFFECT BRAIN OR NERVOUS SYSTEM CAUSING DIZZINESS,HEADACHE OR NAUSEA. CAUSES RESPIRATORY TRACT, EYEAND SKIN IRRITATION. FOR INDUSTRIAL OR COMMERCIAL USE ONLY.KEEP OUT OF REACH OF CHILDREN. SEE THE PRODUCT MATERIALSAFETY DATA SHEET (MSDS) AND LABEL WARNINGS FORADDITIONAL SAFETY INFORMATION.Calculated values are shown and may vary slightly from the actual manufactured material.3 of 4Form: 206721Rev. 4/03Printed in USA

The technical data and suggestions for use contained herein are correct to the best of our knowledge, and offered in good faith. The statements of this literature do not constitutea warranty, express, or implied, as to the performance of these products. As conditions and use of our materials are beyond our control, we can guarantee these products onlyto conform to our standards of quality, and our liability, if any, will be limited to replacement of defective materials. All technical information is subject to change without notice.RUST-OLEUM INDUSTRIAL BRANDSPRODUCTS THAT WORK AS HARD AS YOU DO.Rust-Oleum Corporation11 Hawthorn Parkway | Vernon Hills, Illinois 60061 | Phone: (847) 367-7700 | www.rustoleum.comAn RPM Company4 of 4Form: 206721Rev. 4/03Printed in USA