Brocade MLX Series and Brocade NetIron XMR Diagnostic Guide ...

802.1ag CFM for VPLS debug commands 3Dec 10 20:00:55 CFM configuration for Vlan 3004 deleted due to vlan configurationchangesDec 10 20:00:55 dot1ag_clean_cfm_port_for_ma:1Dec 10 20:00:55 Send MA CO to LP: md test ma 3004 Add 0Dec 10 20:00:55 CFM configuration for Vlan 3005 deleted due to vlan configurationchangesDec 10 20:00:55 dot1ag_clean_cfm_port_for_ma:1Dec 10 20:00:55 Send MA CO to LP: md test ma 3005 Add 0Dec 10 20:00:55 CFM configuration for Vlan 3006 deleted due to vlan configurationchangesDec 10 20:00:55 dot1ag_clean_cfm_port_for_ma:1Dec 10 20:00:55 Send MA CO to LP: md test ma 3006 Add 0Dec 10 20:00:55 CFM configuration for Vlan 3007 deleted due to vlan configurationchangesDec 10 20:00:55 dot1ag_clean_cfm_port_for_ma:1Dec 10 20:00:55 Send MA CO to LP: md test ma 3007 Add 0Dec 10 20:00:55 CFM configuration for Vlan 3008 deleted due to vlan configurationchangesDec 10 20:00:55 dot1ag_clean_cfm_port_for_ma:1Dec 10 20:00:55 Send MA CO to LP: md test ma 3008 Add 0Brocade(config-vlan-group-1)#endSYSLOG: Dec 10 20:01:06 Dist1 Security: running-config was changed fromconsoledebug cfm packetSyntax: [no] debug cfm packetThis command enables debugging and displays information about CFM packets. This command isused to monitor the receipt of the ETH-DM packet on the LP.NOTEThis is a generic debug command and displays the information for all CFM packets as well.debug cfm detailSyntax: [no] debug cfm detailThis command is used to dump the contents (time stamps) of the ETH-DM packet.NOTEThis is a generic debug command and displays the information for all CFM packets as well.The debug cfm packet and debug cfm detail command output resembles the following example.Brocade# debug cfmBrocade(config-cfm)# cfm-enableBrocade(config-cfm)# domain-name test id 1 level 7Brocade(config-cfm-md-test)# ma-name 3001 id 1 vlan-id 3001 priority 0Dec 10 20:38:03 Send MA CO to LP: md test ma 3001 Add 1Dec 10 20:38:03 dot1ag_default_create_mipDec 10 20:38:03 dot1ag_create_cfm_port vlan_id 3001 port_id 3/1 is_mep 0 is_mp 1Dec 10 20:38:03 Send CFM port to LP: vlan 3001 port 3/1Dec 10 20:38:03 level 7 is valid, is MEP 0, mep-id 0, is MIP 1Brocade(config-cfm-md-test-ma-3001)# ma-name 3002 id 2 vlan-id 3002 priority 1Dec 10 20:38:03 Send MA CO to LP: md test ma 3002 Add 1Dec 10 20:38:03 dot1ag_default_create_mipDec 10 20:38:03 dot1ag_create_cfm_port vlan_id 3002 port_id 3/1 is_mep 0 is_mp 1Dec 10 20:38:03 Send CFM port to LP: vlan 3002 port 3/1Dec 10 20:38:03 level 7 is valid, is MEP 0, mep-id 0, is MIP 1Brocade(config-cfm-md-test-ma-3002)# ma-name 3003 id 3 vlan-id 3003 priority 2Brocade MLX Series and Brocade NetIron XMR Diagnostic Guide 7153-1002426-02