Brocade MLX Series and Brocade NetIron XMR Diagnostic Guide ...

PIM DM and PIM SM 8Brocade# show ip pim nbrPort Neighbor Holdtime Age UpTimesec sec sece3/8 207.95.8.10 180 60 900Port Neighbor Holdtime Age UpTimesec sec secv1 207.95.6.2 180 60 900show ip pim mcacheSyntax: show ip pim mcache • - Specifies the IP source or group address.This command displays information about the PIM multicast cache, as shown in the followingexample.Brocade# show ip pim mcacheTotal 3 entries1 (10.161.32.200, 237.0.0.1) in v87 (tag e3/1), cnt=0Sparse Mode, RPT=0 SPT=1 Reg=0upstream neighbor=10.10.8.45num_oifs = 1 v2L3 (HW) 1: e4/24(VL2702)fast=1 slow=0 leaf=0 prun=0 frag=0 tag=0 tnnl=0 swL2=0 hwL2=0 msdp_adv=0age=0 fid: 0416 l2vidx: none2 (*, 237.0.0.1) RP10.161.2.1 in v93, cnt=0Sparse Mode, RPT=1 SPT=0 Reg=0upstream neighbor=10.10.8.33num_oifs = 1 v2L3 (SW) 1: e4/24(VL2702)fast=1 slow=0 leaf=0 prun=0 frag=0 tag=0 tnnl=0 swL2=0 hwL2=0 msdp_adv=0age=0 fid: none l2vidx: none3 (*, 239.255.255.250) RP10.159.2.2 in v87, cnt=0Sparse Mode, RPT=1 SPT=0 Reg=0upstream neighbor=10.10.8.45num_oifs = 1 v2L3 (SW) 1: e4/23(VL2702)fast=1 slow=0 leaf=0 prun=0 frag=0 tag=0 tnnl=0 swL2=0 hwL2=0 msdp_adv=0age=0 fid: none l2vidx: noneWhen debug is enabled for a particular group, the output of the show ip pim mcache commandresembles the following example.Brocade# show ip pim mcache 165.165.165.103 226.10.10.31 (165.165.165.103, 226.10.10.3) in v20 (NIL), cnt=0. Addr 0x34a3a4f1Sparse Mode, RPT=0 SPT=0 Reg=0 L2Reg=0 RegSupp=0 RegProbe=0 LSrc=0 LRcv=0upstream neighbor=20.20.20.3num_oifs = 4inherited_oifs = 4, blocked_oifs = 020,2/1(00:07:05/25) Flags:00000003 1,2/15(00:07:11/35) Flags:000000021,2/19(00:07:36/0) Flags:00000002 10,2/19(00:07:58/0) Flags:00000002slow ports ethe 2/19L3 (SW) 4: e2/1(VL20), e2/15(VL1), e2/19(VL1), e2/19(VL10),Flags (0x700200c0)sm=1 ssm=0 hw=1 fast=0 slow=0 leaf=0 prun=0 tag=0 needRte=0 msdp_adv=0AgeSltMsk=00000000, FID: 0x8003 MVID: NotReqBrocade MLX Series and Brocade NetIron XMR Diagnostic Guide 29353-1002426-02