Brocade MLX Series and Brocade NetIron XMR Diagnostic Guide ...

MPLS API 6Dec 10 00:59:58 RSIR: CSPF Begin FRR BYPASS_CSPF route calculationDec 10 00:59:58 RSIR: CSPF End FRR BYPASS_CSPF route calculation. Route not found,error_code: 1Dec 10 00:59:58 CSPF failed to calculate bypass route to 17.1.17.1Dec 10 00:59:58 MPLS: CSPF: RSIR: BYPASS_CSPF: My IP address from upstream entry:17.1.17.2Num_hops downstream 1, upstream 1, exclude 1Dec 10 00:59:58 MPLS: CSPF: RSIR: BYPASS_CSPF: Finding Bypass path to: 17.1.17.1Dec 10 00:59:58 RSIR: BYPASS_CSPF: Constraints: BW: 0 kbps Setup Prio: 4Hop-Limit: 255exc-any: 0x0X00000000 inc-any: 0x0X00000000 inc-all: 0x0X00000000Dec 10 00:59:58 RSIR: BYPASS_CSPF: Removed link local IP: 17.1.17.2Dec 10 00:59:58 RSIR: CSPF Begin FRR BYPASS_CSPF route calculationDec 10 00:59:58 RSIR: CSPF End FRR BYPASS_CSPF route calculation. Route not found,error_code: 1debug mpls forwarding resourceSyntax: [no] debug mpls forwarding resourceThis command displays information about available MPLS resources. Command output resemblesthe following example.Brocade# debug mpls forwarding resourceCheck BW:Path_TSpec valid: BW = 50 Kb/secResv_TSpec valid: BW = 50 Kb/secAlloc BW[outseg idx: 7]: setup/hold priority 7/0:Path_TSpec valid: BW = 50 Kb/secResv_TSpec valid: BW = 50 Kb/secAllocated BW 50 kbps for priority 0MPLS routing debug commandsThis section describes the debug commands that generate MPLS routing information.debug mpls routingSyntax: [no] debug mpls routing [all | error | interface | prefix]This command displays MPLS routing-related information.• all - Displays all debug messages related to MPLS routing.• error - Displays MPLS routing-related error messages.• interface - Limits the messages to specific interfaces. This filter captures the event of aparticular IP interface indication (or polling) by routing stub module to MPLS.• prefix - Limits the messages to specific prefixes. The purpose of this filter is to trace aparticular IP route notification by routing module to MPLS.Command output resembles the following example.Brocade# debug mpls routingRSIR skip route add: 1.1.1.0/24, ingr(0), egr(0)RSIR port state change indication for e1/1: Admin: UP Oper: UPRSIR IP address indication to RRI for e1/1: addr add 1.1.1.2/24RSIR IP address indication to RCP for e1/1: addr add 1.1.1.2/24RSIR IP address indication to RCS for e1/1: addr add 1.1.1.2/24RSIR route add(RSVP) indication: 1.1.2.0/24, idx 0x0X0A3682E6, sh_cut0x0X00000000 nh 1.1.2.0, intf e1/2, ingr 0, egr 0, r_flag 0x0X00000000RSIR skip route add: 1.1.2.0/24, ingr(0), egr(0)Brocade MLX Series and Brocade NetIron XMR Diagnostic Guide 20353-1002426-02