English - Service après vente - Dewalt

More documents

Recommendations

Info

ENGLISHCAUTION: If the guard cannot betightened by the adjusting screw, donot use the tool. To reduce the risk ofpersonal injury, take the tool and guardto a service center to repair or replacethe guard.Fitting and Removing a Grinding orCutting Disc (fig. 3–5)WARNING: Do not use a damageddisc.1. Place the tool on a table, guard up.2. Fit the backing flange (j) correctly onto thespindle (k) (fig. 3).3. Place the disc (l) on the backing flange (j) (fig. 4).When fitting a disc with a raised center, makesure that the raised centre (m) is facing thebacking flange (j).4. Screw the threaded clamp nut (n) onto thespindle (k) (fig. 5):a. The ring on the threaded clamp nut (n) mustface towards the disc when fitting a grindingdisc (fig. 5A);b. The ring on the threaded clamp nut (n) mustface away from the disc when fitting a cuttingdisc (fig. 5B).5. Press the spindle lock button (c) and rotate thespindle (k) until it locks in position (fig. 4).6. Tighten the threaded clamp nut (n) with the twopinspanner supplied.7. Release the spindle lock.8. To remove the disc, loosen the threaded clampnut (n) with the two-pin spanner.Prior to Operation• Install the guard and appropriate disc or wheel.Do not use excessively worn discs or wheels.• Be sure the inner and outer flange are mountedcorrectly.• Make sure the disc or wheel rotates in thedirection of the arrows on the accessory and thetool.OPERATIONInstructions for UseWARNING: Always observe the safetyinstructions and applicable regulations.WARNING: To reduce the riskof serious personal injury, turntool off and disconnect tool frompower source before making anyadjustments or removing/installingattachments or accessories. Beforereconnecting the tool, depress andrelease the trigger switch to ensure thatthe tool is off.WARNING:• Ensure all materials to be ground orcut are secured in place.• Apply only a gentle pressure to thetool. Do not exert side pressure on thedisc.• Avoid overloading. Should the toolbecome hot, let it run a few minutesunder no load condition.Proper Hand Position (fig. 1)WARNING: To reduce the risk ofserious personal injury, ALWAYS useproper hand position as shown.WARNING: To reduce the risk ofserious personal injury, ALWAYS holdsecurely in anticipation of a suddenreaction.Proper hand position requires one hand on the sidehandle (e), with the other hand on the body of thetool, as shown in figure 1.Switching On and Off (fig. 1)The on/off switch is equipped with an unlockingswitch.To run the tool, depress the unlocking switch (b) andsubsequently operate the on/off switch (a).Release the unlocking switch (b).To stop the tool,release the switch.Spindle Lock (fig. 1)The spindle lock (c) is provided to prevent thespindle from rotating when installing or removingwheels. Operate the spindle lock only when the toolis turned off, unplugged from the power supply, andhas come to a complete stop.NOTICE: To reduce the risk of damageto the tool, do not engage the spindlelock while the tool is operating. Damageto the tool will result and attachedaccessory may spin off possiblyresulting in injury.12
ENGLISHTo engage the lock, depress the spindle lock buttonand rotate the spindle until you are unable to rotatethe spindle further.Metal ApplicationsWhen using the tool in metal applications, makesure that a residual current device (RCD) has beeninserted to avoid residual risks caused by metalswarf.If the power supply is shut off by the RCD, take thetool to authorised DEWALT repair agent.WARNING: In extreme workingconditions, conductive dust canaccumulate inside the machine housingwhen working with metal. This can resultin the protective insulation inthe machinebecoming degraded with a potential riskof an electrical shock.To avoid build-up of metal swarf inside the machine,we recommend to clear the ventilation slots on adaily basis. Refer to Maintenance.Using Flap DiscsWARNING: Metal dust build-up.Extensive use of flap discs in metalapplications can result in the increasedpotential for electric shock. To reducethis risk, insert an RCD before useand clean the ventilation slots daily byblowing dry compressed air into theventilation slots inaccordance with thebelow maintenance instructions.MAINTENANCEYour DEWALT power tool has been designed tooperate over a long period of time with a minimumof maintenance. Continuous satisfactory operationdepends upon proper tool care and regular cleaning.WARNING: To reduce the riskof serious personal injury, turntool off and disconnect tool frompower source before making anyadjustments or removing/installingattachments or accessories. Beforereconnecting the tool, depress andrelease the trigger switch to ensure thatthe tool is off.Pop-off BrushesThe motor will be automatically shut off indicatingthat the carbon brushes are nearly worn out andthat the tool needs servicing. The carbon brushesare not user-serviceable. Take the tool to anauthorised DEWALT repair agent.LubricationYour power tool requires no additional lubrication.CleaningWARNING: Blow dirt and dust out ofthe main housing with dry air as often asdirt is seen collecting in and around theair vents. Wear approved eye protectionand approved dust mask whenperforming this procedure.WARNING: Never use solvents orother harsh chemicals for cleaning thenon-metallic parts of the tool. Thesechemicals may weaken the materialsused in these parts. Use a clothdampened only with water and mildsoap. Never let any liquid get inside thetool; never immerse any part of the toolinto a liquid.Optional AccessoriesWARNING: Since accessories, otherthan those offered by DEWALT, havenot been tested with this product, useof such accessories with this tool couldbe hazardous. To reduce the risk ofinjury, only DEWALT, recommendedaccessories should be used with thisproduct.Consult your dealer for further information on theappropriate accessories.Protecting the EnvironmentSeparate collection. This product mustnot be disposed of with normalhousehold waste.Should you find one day that your DEWALT productneeds replacement, or if it is of no further use to you,do not dispose of it with household waste. Make thisproduct available for separate collection.Separate collection of used products andpackaging allows materials to berecycled and used again. Re-use ofrecycled materials helps pre<strong>vente</strong>nvironmental pollution and reducesthe demand for raw materials.13
Page 1 and 2: www..euD28410D28411D28413D28414D284
Page 3: Figure 1bcaedt1
Page 8 and 9: ENGLISHEC-Declaration of Conformity
Page 10 and 11: ENGLISHg) Wear personal protective
Page 12 and 13: ENGLISHResidual RisksIn spite of th
Page 16 and 17: ENGLISHLocal regulations may provid
Page 18: ENGLISHGRINDING AND CUTTING ACCESSO

English - Service après vente - Dewalt

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?