2005 MY OBD System Operation Summary for Gasoline Engines

More documents

Recommendations

Info

0.020” EVAP Monitor Operation:DTCsMonitor executionMonitor SequenceSensors/Components OKMonitoring DurationP0455 (gross leak),P1450, (excessive vacuum),P0457 (gross leak, cap off),P0442 (0.040” leak),P0456 (0.020” leak)once per driving cycle for 0.040” dia leakonce per driving cycle, no refueling event for 0.020” dia leakHO2S monitor for front sensors completed and OKMAF, IAT, VSS, ECT, CKP, TP, FTP, VMV, CVS360 seconds for 0.040” (see disablement conditions below)60 seconds for 0.020” (see disablement conditions below)Typical 0.020” EVAP monitor entry conditions, Phases 0 through 4:Entry condition Minimum MaximumEngine off (soak) time6 hoursTime since engine start-up for 0.040” 330 seconds 1800 to 2700secondsTime since engine start-up for 0.020” idle test 30 seconds 600 secondsRefueling event (for 0.020” idle test only)Intake Air Temp for 0.040” 40 o F 90 - 100 o FnoneIntake Air Temp for 0.020” 40 o F 90 o FVehicle Speed for cruise test, 0.040 and 0.020” 40 mph 80 mphVehicle Speed for idle test, 0.020”Fuel Fill Level for 0.040” 15% 85%Fuel Fill Level for 0.020” 15 - 30% 85%BARO (
Typical 0.020” EVAP abort (fuel slosh) conditions for Phase 2:Change in load: > 20% for 0.040”Change in load: > 10% for 0.020”Change in tank pressure: > 1 “ H 2 O for 0.040”Change in tank pressure: > 1 “ H 2 O for 0.020”Change in fuel fill level: > 15% for 0.040”Change in fuel fill level: > 8% for 0.020”Number of aborts: > 20 (may be up to 255)Typical 0.020 EVAP monitor malfunction thresholds:P1450 (Excessive vacuum): < -8.0 in H 2 O over a 30 second evaluation time or > -4. in H 2 O vapor generation.P0455 (Gross leak): > -8.0 in H 2 O over a 30 second evaluation time.P0457 (Gross leak, cap off): > -8.0 in H 2 O over a 30 second evaluation time after a refueling event.P0442 (0.040” leak): > 2.5 in H 2 O bleed-up over a 15 sec. evaluation time at 75% fuel fill.(Note: bleed-up and evaluation times vary as a function of fuel fill level and ambient temperature).P0456 (0.020” leak): > 2.5 in H 2 O bleed-up over a 30 sec. evaluation time at 75% fuel fill.(Note: bleed-up and evaluation times vary as a function of fuel fill level and ambient temperature)P0442 vapor generation limit: < 2.5 in H 2 O over a 100 second evaluation time.J1979 Evaporative System Mode $06 DataTest ID Comp ID Description for J1850 Units$26 $00 Phase 0 Initial tank vacuum and minimum limit in H 2 0$26 $00 Phase 0 Initial tank vacuum and maximum limit in H 2 0$27 $00 Phase 2 0.040” cruise leak check vacuum bleed-up andmaximum 0.040” leak threshold$28 $00 Phase 2 0.020” cruise leak check vacuum bleed-up and maxleak threshold$2A $00 Phase 4 Vapor generation maximum change in pressure andmax threshold$2B $00 Phase 4 Vapor generation maximum absolute pressure rise andmax threshold$2C $00 Phase 2 0.020” idle leak check vacuum bleed-up and maximum“leak” threshold$2D $00 Phase 2 0.020” idle leak check vacuum bleed-up and max “noleak”thresholdin H 2 0in H 2 0in H 2 0in H 2 0in H 2 0in H 2 0Conversion for Test IDs $26 through $2D: Take value, subtract 32,768, and then multiply result by 0.00195 toget inches of H20. The result can be positive or negative.Note: Default values (-64 in H 2 0) will be display for all the above TIDs if the evap monitor has nevercompleted. If all or some phases of the monitor have completed on the current or last driving cycle, defaultvalues will be displayed for any phases that had not completed.FORD MOTOR COMPANY REVISION DATE: APRIL 28, 2004 PAGE 25 OF 131
Page 1: Table of ContentsIntroduction - OBD
Page 4 and 5: !The Catalyst Efficiency Monitor us
Page 6 and 7: TYPICAL INDEX RATIO CATALYST MONITO
Page 8 and 9: There are three different misfire m
Page 10 and 11: 0#1The acceleration that a piston u
Page 12 and 13: J1979 Misfire Mode $06 DataTest ID
Page 14 and 15: 0$Secondary air systems typically u
Page 16 and 17: 201 34536/#/Vehicles that meet enha
Page 18 and 19: 0.040” EVAP Monitor Operation:DTC
Page 20 and 21: 201 3536/#/Some vehicles that meet
Page 22 and 23: slosh. If the monitor aborts, it wi
Page 26 and 27: Test ID Comp ID Description for J18
Page 28 and 29: Ford's EONV implementation for Cali
Page 30 and 31: 1#4;!In this phase, the EONV test i
Page 32 and 33: 0.020” EONV EVAP Monitor Operatio
Page 34 and 35: 201!!#/Additional malfunctions that
Page 36 and 37: Fuel Tank Pressures Sensor Offset C
Page 38 and 39: :As fuel system components age or o
Page 40 and 41: -:-The time between HO2S switches i
Page 42 and 43: $-A functional test of the rear HO2
Page 44 and 45: -- 3 amps, (NTK)< 0.400 amps or > 3
Page 46 and 47: 1:$The Delta Pressure Feedback EGR
Page 48 and 49: If an EGR system malfunction is det
Page 50 and 51: After the vehicle has warmed up and
Page 52 and 53: 1:$In the 2002.5 MY, Ford introduce
Page 54 and 55: The ESM may provide the PCM with a
Page 56 and 57: Next, the differential pressure ind
Page 58 and 59: I/M Readiness IndicationIf the infe
Page 60 and 61: The Stepper Motor EGR Monitor consi
Page 62 and 63: Note: BARO is inferred at engine st
Page 64 and 65: $. 6The Electric Stepper Motor EGR
Page 66 and 67: The MAP sensor is also checked for
Page 68 and 69: When the entry conditions for the f
Page 70 and 71: 1!2Ford plans to comply with the PC
Page 72 and 73: ETC System Failure Mode and Effects
Page 74 and 75:
;#11!%;11!)The purpose of the TPPC
Page 76 and 77:
Currently, vehicles use either an E
Page 78 and 79:
Fuel Rail Pressure Sensor Check Ope
Page 80 and 81:
Loss of Keep Alive Memory (KAM) pow
Page 82 and 83:
CKP Ignition System Check Operation
Page 84 and 85:
The Idle Air Control (IAC) solenoid
Page 86 and 87:
There are several different styles
Page 88 and 89:
The PCM continually calculates a ca
Page 90 and 91:
Most vehicle applications no longer
Page 92 and 93:
Intermediate Shaft Speed Sensor Fun
Page 94 and 95:
Primary Pulley Speed Sensor Functio
Page 96 and 97:
Secondary Pulley Pressure Sensor Ch
Page 98 and 99:
Typical Shift Solenoid mechanical f
Page 100 and 101:
Shift Completion Check Operation:DT
Page 102 and 103:
Pressure Control Solenoid Check Ope
Page 104 and 105:
Forward Clutch/Reverse Clutch Solen
Page 106 and 107:
4$=%$> );4R70E is the replacement f
Page 108 and 109:
! 4%:> );;The Analog Transmission R
Page 110 and 111:
$%$> );;The Digital Transmission Ra
Page 112 and 113:
Direct One Way ClutchThe Direct One
Page 114 and 115:
Direct One Way ClutchThe Direct One
Page 116 and 117:
$&&> %$> );;Transmission Range Sens
Page 118 and 119:
4:=%:.)%:> );;The Transmission Rang
Page 120 and 121:
CFT 30 Mechatronic Illustration;Tra
Page 122 and 123:
Internal TCM Power SupplyIf the pow
Page 124 and 125:
shift, rpm does not go up during a
Page 126 and 127:
The shift solenoids are monitored f
Page 128 and 129:
*> #606Exponentially Weighted Movin
Page 130 and 131:
@$!The readiness function is implem
show all

2005 MY OBD System Operation Summary for Gasoline Engines

Create successful ePaper yourself

Delete template?

Save as template?