2005 MY OBD System Operation Summary for Gasoline Engines

More documents

Recommendations

Info

Forward Clutch/Reverse Clutch Solenoid Check Operation:DTCsMonitor executionMonitor SequenceSensors OKMonitoring DurationP0900, P0902, P0903 Opens/shorts – CFT30P0810 functional, sticking – CFT30P0811 functional, slippage – CFT30ContinuousNoneElectrical: 0.040 seconds,Mechanical functional: 0.500 secondsTypical Forward Clutch/Reverse Clutch slipping check entry conditions:Entry Conditions Minimum MaximumVehicle Speed OR0.62 mphVehicle Speed16 mphGear selectorDrive or ReverseTypical Forward Clutch/Reverse Clutch stuck check entry conditions:Entry Conditions Minimum MaximumVehicle Speed OR0.62 mphVehicle Speed16 mphGear selectorPark or NeuralTypical Forward Clutch/Reverse Clutch Solenoid malfunction thresholds:Electrical current check: Feedback current out of range for 0.040 secondsSlipping Check: Turbine Speed is > 100 rpm higher than Pulley Speed for 200 ms.Stuck Check: Turbine Speed is within 40 rpm of Pulley Speed for 500 ms.FORD MOTOR COMPANY REVISION DATE: APRIL 28, 2004 PAGE 104 OF 131
4$=> %$> );(no turbine speed sensor);The Digital Transmission Range (DTR) sensor provides a single analog and three digital inputs to the PCM. ThePCM decodes the inputs to determine the driver-selected gear position (Park, Rev, Neutral, OD, 2, 1). This inputdevice is checked for opens and invalid input patterns. (P0708 P0705)The Vehicle Speed Sensor (VSS) and Output Shaft Speed (OSS) sensor, if equipped, are inputs that arechecked for rationality. If the engine rpm is above the torque converter stall speed and engine load is high, it canbe inferred that the vehicle must be moving. If there is insufficient output from the VSS sensor, a malfunction isindicated (P0500). If there is insufficient output from the OSS sensor, a malfunction is indicated (P0720).;Shift SolenoidsThe Shift Solenoid (SSA and SSB) output circuits are checked for opens and shorts by the PCM by monitoringthe status of a feedback circuit from the output driver (P0750 SSA, P0755 SSB).All vehicle applications will utilize an inductive signature circuit to monitor the shift solenoids functionally. The ISIGcircuit monitors the current signature of the shift solenoid as the solenoid is commanded on. A solenoid thatfunctions properly will show a characteristic decrease in current as the solenoid starts to move. If the solenoid ismalfunctioning, the current will not change (P1714 SSA, P1715 SSB). The lack of communication between theISIG chip and the PCM microprocessor is also monitored (P1636).Torque Converter ClutchThe Torque Converter Clutch (TCC) output circuit is a duty-cycled output that is checked electrically for opensand shorts by the PCM by monitoring the status of a feedback circuit from the output driver (P0743).All vehicle applications will utilize an inductive signature circuit to monitor the torque converter clutch. The ISIGcircuit monitors the current signature of the TCC solenoid as the solenoid is commanded on. A solenoid thatfunctions properly will show a characteristic decrease in current as the solenoid starts to move. If the solenoid ismalfunctioning, the current will not change (P1740) . In some applications, the ISIG test is run in conjunction withthe other transmission functional tests. The lack of communication between the ISIG chip and the PCMmicroprocessor is also monitored (P1636).Electronic Pressure ControlThe EPC solenoid is a variable force solenoid that controls line pressure in the transmission. The EPC solenoidhas a feedback circuit in the PCM that monitors EPC current. If the current indicates a short to ground (lowpressure), engine torque may be reduced to prevent damage to the transmission. (P1747, PCA)FORD MOTOR COMPANY REVISION DATE: APRIL 28, 2004 PAGE 105 OF 131
Page 1:
Table of ContentsIntroduction - OBD
Page 4 and 5:
!The Catalyst Efficiency Monitor us
Page 6 and 7:
TYPICAL INDEX RATIO CATALYST MONITO
Page 8 and 9:
There are three different misfire m
Page 10 and 11:
0#1The acceleration that a piston u
Page 12 and 13:
J1979 Misfire Mode $06 DataTest ID
Page 14 and 15:
0$Secondary air systems typically u
Page 16 and 17:
201 34536/#/Vehicles that meet enha
Page 18 and 19:
0.040” EVAP Monitor Operation:DTC
Page 20 and 21:
201 3536/#/Some vehicles that meet
Page 22 and 23:
slosh. If the monitor aborts, it wi
Page 24 and 25:
0.020” EVAP Monitor Operation:DTC
Page 26 and 27:
Test ID Comp ID Description for J18
Page 28 and 29:
Ford's EONV implementation for Cali
Page 30 and 31:
1#4;!In this phase, the EONV test i
Page 32 and 33:
0.020” EONV EVAP Monitor Operatio
Page 34 and 35:
201!!#/Additional malfunctions that
Page 36 and 37:
Fuel Tank Pressures Sensor Offset C
Page 38 and 39:
:As fuel system components age or o
Page 40 and 41:
-:-The time between HO2S switches i
Page 42 and 43:
$-A functional test of the rear HO2
Page 44 and 45:
-- 3 amps, (NTK)< 0.400 amps or > 3
Page 46 and 47:
1:$The Delta Pressure Feedback EGR
Page 48 and 49:
If an EGR system malfunction is det
Page 50 and 51:
After the vehicle has warmed up and
Page 52 and 53:
1:$In the 2002.5 MY, Ford introduce
Page 54 and 55: The ESM may provide the PCM with a
Page 56 and 57: Next, the differential pressure ind
Page 58 and 59: I/M Readiness IndicationIf the infe
Page 60 and 61: The Stepper Motor EGR Monitor consi
Page 62 and 63: Note: BARO is inferred at engine st
Page 64 and 65: $. 6The Electric Stepper Motor EGR
Page 66 and 67: The MAP sensor is also checked for
Page 68 and 69: When the entry conditions for the f
Page 70 and 71: 1!2Ford plans to comply with the PC
Page 72 and 73: ETC System Failure Mode and Effects
Page 74 and 75: ;#11!%;11!)The purpose of the TPPC
Page 76 and 77: Currently, vehicles use either an E
Page 78 and 79: Fuel Rail Pressure Sensor Check Ope
Page 80 and 81: Loss of Keep Alive Memory (KAM) pow
Page 82 and 83: CKP Ignition System Check Operation
Page 84 and 85: The Idle Air Control (IAC) solenoid
Page 86 and 87: There are several different styles
Page 88 and 89: The PCM continually calculates a ca
Page 90 and 91: Most vehicle applications no longer
Page 92 and 93: Intermediate Shaft Speed Sensor Fun
Page 94 and 95: Primary Pulley Speed Sensor Functio
Page 96 and 97: Secondary Pulley Pressure Sensor Ch
Page 98 and 99: Typical Shift Solenoid mechanical f
Page 100 and 101: Shift Completion Check Operation:DT
Page 102 and 103: Pressure Control Solenoid Check Ope
Page 106 and 107: 4$=%$> );4R70E is the replacement f
Page 108 and 109: ! 4%:> );;The Analog Transmission R
Page 110 and 111: $%$> );;The Digital Transmission Ra
Page 112 and 113: Direct One Way ClutchThe Direct One
Page 114 and 115: Direct One Way ClutchThe Direct One
Page 116 and 117: $&&> %$> );;Transmission Range Sens
Page 118 and 119: 4:=%:.)%:> );;The Transmission Rang
Page 120 and 121: CFT 30 Mechatronic Illustration;Tra
Page 122 and 123: Internal TCM Power SupplyIf the pow
Page 124 and 125: shift, rpm does not go up during a
Page 126 and 127: The shift solenoids are monitored f
Page 128 and 129: *> #606Exponentially Weighted Movin
Page 130 and 131: @$!The readiness function is implem
show all

2005 MY OBD System Operation Summary for Gasoline Engines

Create successful ePaper yourself

Delete template?

Save as template?