12/131 <strong>Bosch</strong> <strong>Rexroth</strong> AG | Electric Drivesand Controls<strong>Rexroth</strong> <strong>MKE</strong> Synchronous Motors | <strong>Project</strong> <strong>Planning</strong> <strong>Manual</strong>Important Instructions on Use2.2 Inappropriate UseThe <strong>MKE</strong> motors may only be used with the accessories specifiedin the documentation. Components that are not explicitly mentionedmay be neither attached nor connected. The same is true for cablesand lines.Operation may be carried out only in the explicitly mentioned configurationsand combinations of the component and with the softwareand firmware specified in the corresponding functionaldescription.Any connected drive controller must be programmed before startup in order toensure that the motor executes the functions specific to the particular application.<strong>MKE</strong> motors may only be operated under the assembly, mounting and installationconditions, in the normal position, and under the ambient conditions(temperature, degree of protection, humidity, EMC, and the like) specified inthis documentation.Any use of <strong>MKE</strong> motors outside of the fields of application mentioned above orunder operating conditions and technical data other than those specified in thisdocumentation is considered to be "inappropriate use".<strong>MKE</strong> must not be used if ...●●●the ambient conditions require a higher explosion protection than is indicatedon the motor's name plate.they are subject to operating conditions which do not comply with the ambientconditions described above. For example, they must not be operatedunder water, under extreme temperature fluctuations or extreme maximumtemperatures.the intended application is not explicitly approved by <strong>Bosch</strong> <strong>Rexroth</strong>.Please also observe the statements made in the general notes regardingsafety.
<strong>Project</strong> <strong>Planning</strong> <strong>Manual</strong> | <strong>Rexroth</strong> <strong>MKE</strong> Synchronous Motors Electric Drivesand Controls| <strong>Bosch</strong> <strong>Rexroth</strong> AG 13/131Safety Instructions for Electric Drives and Controls3 Safety Instructions for Electric Drives and Controls3.1 Definitions of TermsApplication DocumentationComponentControl SystemDeviceDrive SystemElectrical EquipmentInstallationMachineManufacturerProduct<strong>Project</strong> <strong>Planning</strong> <strong>Manual</strong>Qualified PersonsThe entire documentation used to inform the user of the product about the useand safety-relevant features for configuring, integrating, installing, mounting,commissioning, operating, maintaining, repairing and decommissioning theproduct. The following terms are also used for this kind of documentation: UserGuide, Operation <strong>Manual</strong>, Commissioning <strong>Manual</strong>, Instruction <strong>Manual</strong>, <strong>Project</strong><strong>Planning</strong> <strong>Manual</strong>, Application <strong>Manual</strong>, etc.Combination of elements with a specified function, which are part of a piece ofequipment, device or system. Components of a drive and control system are,for example, supply units, drive controllers, mains choke, mains filter, motors,cables, etc.Several interconnected control components placed on the market as a singlefunctional unit.Finished product with a defined function, intended for users and placed on themarket as an individual piece of merchandise.A group of components consisting of electric motor(s), motor encoder(s) andcable(s), supply units and drive controllers, as well as possible auxiliary andadditional components, such as mains filter, mains choke, etc.Objects used to generate, convert, transmit, distribute or apply electrical energy,such as machines, transformers, switching devices, cables, lines, powerconsumingdevices, circuit board assemblies, plug-in units, control cabinets,etc.Several devices or systems interconnected for a defined purpose and on a definedsite which, however, are not intended to be placed on the market as asingle functional unit.Entirety of interconnected parts or units at least one of which is movable. Thus,a machine consists of the appropriate machine drive elements, as well as controland power circuits, which have been assembled for a specific application.A machine is, for example, intended for processing, treatment, movement orpackaging of a material. The term "machine" also covers a combination of machineswhich are arranged and controlled in such a way that they function as aunified whole.Individual or legal entity bearing responsibility for the design and manufactureof a product which is placed on the market in the individual's or legal entity'sname. The manufacturer can use finished products, finished parts or finishedelements, or contract out work to subcontractors. However, he must alwayshave overall control and possess the required authority to take responsibilityfor the product.Produced device, component, part, system, software, firmware, among otherthings.Part of the application documentation used to support the dimensioning andplanning of systems, machines or installations.In terms of this application documentation, qualified persons are those personswho are familiar with the installation, mounting, commissioning and operationof the components of the drive and control system, as well as with the hazardsthis implies, and who possess the qualifications their work requires. To complywith these qualifications, it is necessary, among other things,●to be trained, instructed or authorized to switch electric circuits and devicessafely on and off, to ground them and to mark them,