Bosch Rexroth IndraDyn S - MKE Project Planning Manual

More documents

Recommendations

Info

102/131 Bosch Rexroth AG | Electric Drivesand ControlsRexroth MKE Synchronous Motors | Project Planning ManualInstallation1 Sealing2 Screwed connection3 Cable sealing4 Pressure piece5 Union nut6 Encoder cable7 Power cables8 Lid screws9 Terminal box lidFig.11-2: Connection of MKE037, -047, -0981. Remove the lid screws (8) and take off the terminal box lid (9).The lid screws are coated with TFL. By screwing in resp. out of lidscrews, the coating will be destroyed. When assembling the terminalbox lid, use only the added, coated lid screws.The Eexd-Cable screwings are mounted factory-attached. The sealing(1) is screwed with with the screwing (2) on the terminal box lid (9)(tightening torque of Nm). – The terminal box includes the complete accessoryincl. assembly instruction.2. Insert the union nut (5), the preasure piece (4) and the cable sealing (3)in the indicated order over the power cable (7)3. Tighten the screwing (2) with the sealing (1) within the terminal box lid (9)with tightening torque of 50 Nm.4. Insert the power cable (7) through the screwing (2) into the terminal boxlid (9).5. Remove the EExd-Cable screwing for the encoder cable.When using the ready-made cables of Rexroth, the EExd cablescrewing on the motor is not needed.6. Insert the encoder cable (6) into the terminal box lid (9) (see Fig.11-4 ).7. Tighten the screwing of the encoder cable (2) with the sealing (1) withinthe terminal box lid (9) with tightening torque of 50 Nm.8. Pull back the cable until the shrinking sleeve penetrates the inside of theterminal box by about 16mm (see Fig.: 11-4).
Project Planning Manual | Rexroth MKE Synchronous Motors Electric Drivesand Controls| Bosch Rexroth AG 103/131Installation9. Tighten the union nuts (5) on the screwing (2) with a tightening torque of15 Nm ±10 %.10. Connect the ring terminal (10) and (11) on X5 within the terminal box lid(9) (tightening torque 1.3 Nm ±10 %).11. Connect plug-in terminals X1 and X2 according to terminal diagram (seeFig.: 8-4) to the power cable.12. Connect the plug-in terminals X1 and X2 into the appropriate position ofthe motor connection plate.13. Safe the plug-in terminals X1 with the connection screw of the printedcircuitboard socket.14. Mount the plug-in interlock on the encoder connector X3 (see Fig. 11-3).Fig.11-3:Plug-in interlock15. Connect the encoder connector X2 to the motor connection plate.16. Set the terminal box lid (9) on the motor. Make sure that no wire can becrushed or damaged.17. Tighten the terminal box lid (9) with the added TFL-coated lid screws (8)with 6.1 Nm.If substitude is necessary, please use for lid screws (8) only IS-Screws according to DIN 4762 with a minimum consistency of 8.8!In case of repeated assembling of the terminal box lid, we recommendto secure the lid screws (8) with Loctite 243.
Page 1:
Electric DrivesLinear Motion andand
Page 4 and 5:
II/VIBosch Rexroth AG | Electric Dr
Page 6 and 7:
IV/VIBosch Rexroth AG | Electric Dr
Page 8 and 9:
VI/VIBosch Rexroth AG | Electric Dr
Page 10 and 11:
8/131 Bosch Rexroth AG | Electric D
Page 12 and 13:
10/131 Bosch Rexroth AG | Electric
Page 14 and 15:
Page 16 and 17:
Page 18 and 19:
Page 20 and 21:
Page 22 and 23:
Page 24 and 25:
Page 26:
Page 29 and 30:
Project Planning Manual | Rexroth M
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Page 53 and 54: Project Planning Manual | Rexroth M
Page 103: Project Planning Manual | Rexroth M
show all

Bosch Rexroth IndraDyn S - MKE Project Planning Manual

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?