hxe4b battery powered crimp tool datasheet - Daniels Manufacturing ...

More documents

Recommendations

Info

HXE4BBATTERY POWERED CRIMP TOOLDATASHEETOperationLED Work Light (White)This LED automatically turns on when the trigger is pulled. Itremains on for 10 seconds after the trigger is released.LED Indicator (Red)This tool is equipped with a special circuit boardincorporating several important features to inform the userabout the current status of the unit. The Red LED on theside of the tool signals in the following cases:What Happens… Signal What it Means…Flashing for 2seconds•• Battery is inserted in toolConstant light for 20Battery charge is below 17V atseconds at end of ____beginning of cyclecycleTool will not start,and constant lightfor 20 seconds whentrigger is releasedTool will stop, andconstant light for 20seconds after triggeris releasedTool will stop, andflashing light for 20seconds whentrigger is released________••••Battery charge is below 16V atbeginning of cycleBattery voltage drops below 13Vduring cycleMotor current exceeds 20A duringcycleCircuit has become too hotPressure SensorThis tool is equipped with a pressure sensor that alerts theuser of an incomplete crimp. If the tool is manually retracted before completion ofa crimp, the red LED and audible beep will be activefor 2 seconds. If the tool is unable to reach the required crimpforce, the red LED, work light, and an audible beepwill pulse until after the trigger is released.Installing Dies1. Align die rail slots in die halves with the rail in thecrimp tool and push shank of dies into holes. Dieswill snap into place. (See Figure 1)2. Cycle the tool to make sure dies are properly seated.The tool is now ready for use.Die Removal1. With the crimp dies open, place die removal toolagainst end of knockout pin and tap gently with smallhammer. (See Figure 2) The die will be releasedfrom the front die holder. It can now be removed byhand.2. Activate the tool until the movable die extends, butthe tool does not cycle fully. Slide the die removaltool between the die and tool body. (See Figure 3)Press the emergency release button to retract thetool pushrod. The die will be released and can beremoved by hand.________________________________________________________________________________________________HXE4B-DS ©2015 Daniels Manufacturing Corp., All Rights Reserved Page 4 of 7 REV. C 3/12/2015Daniels Manufacturing Corporation526 Thorpe Road, Orlando, FL 32824 USAPhone: 407-855-6161 Fax: 407-855-6884 Email: DMC@dmctools.com
HXE4BBATTERY POWERED CRIMP TOOLPermanent Die Assembly1. Install dies in crimp tool.2. Drive lock pins, supplied with dies, through holes andflush with outside surfaces. Long pin through toolbody and short pin through push rod. (See Figure 4)Preparing CableFollow the lug/connector manufacturer’s instructions forappropriate cable strip length, and contact/wire assembly.Crimping Cable1. Insert the properly assembled connector into thecrimping head.2. Pull the trigger to make the crimp.3. Hold the trigger down until crimping tool achievespressure relief, which is accompanied by an audible“pop”.4. The crimp tool push rod retracts automatically.CAUTION! DO NOT OPERATE TOOL WITHOUT DIE SETIN PLACENote: If it is necessary to retract the tool push rod before acrimp cycle is completed, push and hold the EmergencyRelease button. Pushing and holding the EmergencyRelease button will result in the complete retraction of thepush rod.Gaging Die sets in the tool1. Ensure die set is properly installed in the tool2. Remove fingers/hands/ etc. from crimping area3. Jog the trigger by pulling and letting go quickly untilthe die faces are touching and will not slide on eachother with moderate hand pressure.4. Use appropriate GO/NO-GO gage for the die set tocheck conformance to appropriate dimensions.5. Remove GO/NO-GO gage from die6. Hold the trigger down until the cycle completes andthe dies retract to the open position.MaintenanceEach Operating DayBefore Use:1. Inspect dies for wear or damage such as cracks,gouges, or chips.DATASHEET2. Inspect the tool for damage or leaks. If damage isdetected, return the tool to the DMC repair center forinspection.After Use:1. Wipe all tool surfaces clean with a damp cloth andmild detergent.2. Charge the battery.3. Fully retract the tool push rod.4. Place the tool in the carrying case.5. Store in a cool dry place.Monthly1. Thoroughly clean all surfaces.2. Oil the push rod outer surface.Annually or after 10,000 Crimps1. Return the tool to the DMC repair center forinspection & calibration.Trouble ShootingBefore You Begin1. Make sure that the battery is charged. Recheck thebattery after several minutes to make sure thebattery is holding its charge.2. Use a nonflammable contact cleaner or pencil eraserto clean the electrical contacts on the battery andcrimp tool.3. Reinstall the battery and check the tool again.Problem Probable Cause Probable RemedyTool is inoperative Dirt, contaminants, etc, Clean tool.in ram area of tool.Crimping tool batterycontacts damaged.Tool components worn ordamaged.Reform contacts.Return tool to DMC.Dies stop during Oil level is low. Return tool to DMC.operation.Air in hydraulic system.Pull trigger and holdemergency releasebutton simultaneously.Hold for approximately10 seconds.Tool loses oil. Damaged internal seal. Return tool to DMC.________________________________________________________________________________________________HXE4B-DS ©2015 Daniels Manufacturing Corp., All Rights Reserved Page 5 of 7 REV. C 3/12/2015Daniels Manufacturing Corporation526 Thorpe Road, Orlando, FL 32824 USAPhone: 407-855-6161 Fax: 407-855-6884 Email: DMC@dmctools.com
Page 1 and 2: HXE4BBATTERY POWERED CRIMP TOOLDATA
Page 3: HXE4BBATTERY POWERED CRIMP TOOLDATA

hxe4b battery powered crimp tool datasheet - Daniels Manufacturing ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?