CD(M)1300L - 3 Tuner module for analog and digital cable (QAM ...

More documents

Recommendations

Info

Philips RF SolutionsTuner module for analog and digitalcable (QAM) applicationsProduct specificationCD(M)1300L-3DEFINITION OF TERMINALS / SUPPLY DATAYou.RF-input..RF-output15 13 11 9 7 5 3 114 12 10 8 6 4 2.Terminal Function Remark1n.c.option for RF-outputoption for outdoor unit power supply2 +5V ± 5% splitter (V S )Audio - baseband input3(not connected for tuners without remodulator)Video - baseband input4(not connected for tuners without remodulator)5 External RF-gain control voltage (0.5V - 4.0V)AC - coupledAC - coupledIn case the internal AGCloop is enabled, the max.source impedance is limitedto 200 ohms6 do not connect, leave terminal open for testing only7 PLL chip address select (I 2 C / tuner) see application notes8 SCL (I 2 C / tuner)9 SDA (I 2 C / tuner)10 n.c.11 +5V ± 5% supply tuner (V TU )12 'broadband' IF - output AC coupled13 IF-gain control voltagemax. gain at 3Vmin. gain at 0V(see application notes)14 'narrowband' IF - output AC coupled15 'narrowband' IF - output AC coupled3139 149 11650 12 rev d : 01.09.2005
Philips RF SolutionsTuner module for analog and digitalcable (QAM) applicationsProduct specificationCD(M)1300L-3APPLICATION NOTESProgramming of tuner PLLThe tuner control (frequency selection and band switching) is done via the I 2 C bus.One address byte and four data bytes are needed to fully program the tuner.A PLL lock flag can be read from the tuner during 'READ' - mode.Four independent PLL addresses are available; which one is actually valid depends on the addressselect voltage that is connected to terminal 7.I 2 C-bus data format , ' WRITE ' - mode:BYTE NAME BYTE MSB LSB ACKAddress Byte ADB 1 1 0 0 0 CA2 CA1 R/W=0 ADivider Byte 1 DB1 0 N14 N13 N12 N11 N10 N9 N8 ADivider Byte 2 DB2 N7 N6 N5 N4 N3 N2 N1 N0 AControl Data Byte CB 1 1 0 0 0 RSA RSB 0 ABandswitch byte BB 0 0 0 AGC2 AGC1 SP3 SP2 SP1 AA = acknowledgeDescription of used symbols:CA2, CA1R/WN14 to N0RSA, RSBAGC2, AGC1SP5 ..... SP1: chip address selection bits(see table: Programmable address selection bits): Read / Write bit ; Bit = 0 ⇒ Write modeBit = 1 ⇒ Read mode: LO frequency divider bits: reference divider bits (see table: Reference Divider Settings): RF-AGC loop Take Over Point (TOP) switch ports (optional)(see table: RF-AGC TOP selection): Switch ports; bit = 1 ⇒ port V out is 'ON'bit = 0 ⇒ port V out is 'OFF'(see table: Band selection table)CA2, CA1: Programmable address selection bits:CA2 CA1 Voltage applied to terminal 70 0 0V to 0.1xV TU0 1 terminal open1 0 0.4xV TU to 0.6xV TU1 1 0.9xV TU to 1.0xV TUN14 to N0: programmable divider bits:divider ratio: N = N14x2 14 + N13x2 13 + ... + N1x2 1 + N0How to calculate the divider ratio N :N =( f + f )inputfrefIF⎡ Hz ⎤⎢⎣ Hz ⎥⎦4⋅10(1)64whereby f ref= [ Hz] = 62. 5kHz6IMPORTANT NOTE:Do not set the divider ratio assuch that the tuner is tunedinto extreme conditions i.e. farbelow or far above thespecified frequency ranges.Note (1) : divider ratio to be set with Bits ' RSA and RSB ' (see table below)3139 149 11650 13 rev d : 01.09.2005
Page 1 and 2: RF SOLUTIONSCD(M)1300L - 3Tuner mod
Page 3 and 4: ..Philips RF SolutionsTuner module
Page 5 and 6: .....Philips RF SolutionsTuner modu
Page 7 and 8: Philips RF SolutionsTuner module fo
Page 11: Philips RF SolutionsTuner module fo

CD(M)1300L - 3 Tuner module for analog and digital cable (QAM ...

Create successful ePaper yourself

Delete template?

Save as template?