Wega 401 M2.40 FKW - EWM Hightec Welding GmbH

More documents

Recommendations

Info

Design and functionSelect welding task5.10.2.5 <strong>Welding</strong> parameter ignition time "tZn" diagramNOTEIn the ignition time, the wire feed continues to run at creep speed after the arc is ignited;the ignition behaviour is improved with the optimum setting.The process described below is always used if there is a pause between welding processes ofnot less than 1.5 seconds.Figure 5-11Legend with an explanation of symbols can be found in the MIG/MAG function sequences /operating modes chapter.44099-005224-EW50108.11.2011
Design and functionSelect welding task5.10.3 <strong>M2.40</strong> welding machine control5.10.3.1 Select JOB number (welding task)This microprocessor-controlled control works according to the one-dial operation principle.Only the gas type, material type and wire electrode diameter should be set as the JOB number on thecontrol, as well as welding output via the step switch. This defines the welding task and the systemspecifies the optimum wire feed speed for the required operating point after the "Test button" is pressed.These settings are retained after the machine is switched off. After switching on again, the parameterspreviously set can be used to continue welding.The user has the option to correct the wire feed speed according to the welding task or individualrequirements.The welding task setting can also be made using the two-dial operation principle, however. To do this, setthe "JOB 0" (manual / no program) from the JOB list, the welding voltage on the step switch, and the wirespeed on the rotary dial. Other parameters are set as described under "Using synergic mode".Operating Action ResultelementX xSelect "JOB". When the "JOB" LED lights, press and holddown the button.2 sec. "JOB" LED flashes.The welder uses the filler material inserted and the connected shielding gas to select the JOB numberaccording to the "JOB-LIST". The "JOB-LIST" is a sticker fixed near the wire feed drive unit.Set JOB number (0-24).1 xConfirm selection.094-010488-00500Massivdraht / Solid WireMaterialSG2/3G3/4 Si1CrNiAlMgAlSiGasAr82/18Ar98/2Ar100Ar100%CO 100 2Wire0,8 1,0 1,2 1,6Job-Nr.1526374891317101418111519121620Massivdraht / Solid WireAl99Ar10021222324Manuell / no program0Figure 5-12099-005224-EW50108.11.201145
Page 6: Safety instructionsNotes on the use
Page 9: Safety instructionsGeneralWARNINGEx
Page 12 and 13: Safety instructionsTransport and in
Page 14 and 15: Safety instructionsAmbient conditio
Page 16 and 17: Machine description - quick overvie
Page 26 and 27: Design and functionGeneral5 Design
Page 28 and 29: Design and functionMains connection
Page 30 and 31: Design and functionWelding torch co
Page 32 and 33: Design and functionWelding torch an
Page 34 and 35: Design and functionShielding gas su
Page 36 and 37: Design and functionShielding gas su
Page 38 and 39: Design and functionInserting the wi
Page 40 and 41: Design and functionSelect welding t
Page 50 and 51: Design and functionMIG/MAG function
Page 57 and 58: Rectifying faultsCustomer checklist
Page 59 and 60: Rectifying faultsResetting the cont
Page 61 and 62: Technical dataWega 4018 Technical d
Page 63 and 64: Replaceable partsWire feed rollers1
Page 65 and 66: Appendix ARecommended settings11 Ap

Wega 401 M2.40 FKW - EWM Hightec Welding GmbH

Create successful ePaper yourself

Delete template?

Save as template?