LT-2061 MR-GRID-II Installation Guide Rev0 112707 - Secutron
LT-2061 MR-GRID-II Installation Guide Rev0 112707 - Secutron LT-2061 MR-GRID-II Installation Guide Rev0 112707 - Secutron
Printer Port InterfaceConfiguration ManagerNow open the Configuration Manager. You will be able to find the shortcut in the CADgraphics folder within thePrograms folder in your Start menu.• Click Start.• Select Programs and move your mouse to the CADgraphics folder. There you will find the ConfigurationManager. Open the program.• You will be prompted to enter a password. The default is password.• Click OK.• Choose Setup/System COM Ports. Set the System type to Custom - Single/Network.• Choose the correct COM port and set for 8 data bits, no parity and 1 stop bit. Choose the baud rate to matchthe panel. Set the Channel to 1 and set the Application to CGCustomInt32.exe by pressing thebutton.• Press Done.Note: Be sure to click the Setup button on the COM ports screen and verify that at least one node islisted that points to a MR-GRID-II-defined "System Panel." For further information refer to page 116of the CADgraphics Users Guide.14
MR-GRID-II Installation & Activation GuideSystem WatchThe System Watch program responds to incoming data from every fire alarm and security device on your site, andimmediately alerts your staff to alarms and malfunctions.You can customize your System Watch screen toemphasize information that is important to you. A full description of how to configure System Watch is included inthe CADgraphics manual located on the CD (D:\User's Guide).You will be able to find the shortcut in the CADgraphics folder within the Programs folder in your Start menu.• Click Start.• Select Programs and move your mouse to the CADgraphics folder. There you will find the ConfigurationManager. Open the program.Note: In the System Watch setup under the List Options tab is the setting "Save Column Widths onExit". Leave this box checked until you have the screens set up to suit your requirements. Once thescreens are in this state uncheck the box. Once you uncheck it, closing and restarting the program willreset the column (and other) settings.Be advised that it may take some time to configure the columns to suit your needs.15
- Page 3: MR-GRID-II Installation GuideTable
- Page 7 and 8: MR-GRID-II Installation & Activatio
- Page 9 and 10: MR-GRID-II Installation & Activatio
- Page 11 and 12: MR-GRID-II Installation & Activatio
- Page 13 and 14: MR-GRID-II Installation & Activatio
- Page 15: MR-GRID-II Installation & Activatio
- Page 20 and 21: Activation ProcedureActivation Proc
- Page 22 and 23: Activation ProcedureGenerate an Act
- Page 24 and 25: Activation ProcedureCompose an E-Ma
- Page 28: © 2007 Secutron, Inc.No part of th
<strong>MR</strong>-<strong>GRID</strong>-<strong>II</strong> <strong>Installation</strong> & Activation <strong>Guide</strong>System WatchThe System Watch program responds to incoming data from every fire alarm and security device on your site, andimmediately alerts your staff to alarms and malfunctions.You can customize your System Watch screen toemphasize information that is important to you. A full description of how to configure System Watch is included inthe CADgraphics manual located on the CD (D:\User's <strong>Guide</strong>).You will be able to find the shortcut in the CADgraphics folder within the Programs folder in your Start menu.• Click Start.• Select Programs and move your mouse to the CADgraphics folder. There you will find the ConfigurationManager. Open the program.Note: In the System Watch setup under the List Options tab is the setting "Save Column Widths onExit". Leave this box checked until you have the screens set up to suit your requirements. Once thescreens are in this state uncheck the box. Once you uncheck it, closing and restarting the program willreset the column (and other) settings.Be advised that it may take some time to configure the columns to suit your needs.15
Change language