2007 Police Interceptor Modifier Guide - Digital Ally, Inc.
2007 Police Interceptor Modifier Guide - Digital Ally, Inc. 2007 Police Interceptor Modifier Guide - Digital Ally, Inc.
3-4 Installation ConsiderationsSection 3: Installation ConsiderationsPartition Installation GuidelinesWARNING: The partition and the installation hardware of the partition must notinterfere with the proper operation of the safety belt, safety belt retractor, side impactsensor and the safety belt height adjusters. Failure to follow these instructions may resultin personal injury.WARNING: Installation of prisoner partitions may increase the risk of injury to frontseat occupants if the vehicle is impacted from a high speed rear end collision. This riskshould be balanced by the law enforcement agency against the risk of injury to the officerassociated with prisoner transportation. Failure to follow these instructions may result inpersonal injury.Safety Belt Retractor2007 Police Interceptor Modifier Guide, 2006
Installation Considerations 3-5Section 3: Installation ConsiderationsThe safety belt retractors are located in the base of the B-pillars. The pretensioner located in theretractor is referred to as the ‘‘safety belt retractor pretensioner’’. In the event of an air bagdeployment, pretensioners provide improved occupant protection by rapidly removing slack fromthe safety belt. Removing slack from the safety belt helps to properly position the occupant andallows for maximum effectiveness of the safety belts and the air bags.• Do not use the safety belt retractor bolts for mounting the partition.• Do not mount any partition hardware on the inboard side of the B-pillar within the bottom 305mm (12 in).• Do not mount any partition hardware that will interfere with the proper sealing of the door.Refer to the following illustration for locations that must not be used for partition mounting:2007 Police Interceptor Modifier Guide, 2006
- Page 34 and 35: Electrical 2-11Section 2: Electrica
- Page 36 and 37: Electrical 2-13Section 2: Electrica
- Page 38 and 39: Electrical 2-15Section 2: Electrica
- Page 40 and 41: Electrical 2-17Section 2: Electrica
- Page 42 and 43: Electrical 2-19Section 2: Electrica
- Page 44 and 45: Electrical 2-21Section 2: Electrica
- Page 46 and 47: Electrical 2-23Section 2: Electrica
- Page 48 and 49: Electrical 2-25Section 2: Electrica
- Page 50 and 51: Electrical 2-27Section 2: Electrica
- Page 52 and 53: Electrical 2-29Section 2: Electrica
- Page 54 and 55: Electrical 2-31Section 2: Electrica
- Page 56 and 57: Electrical 2-33Section 2: Electrica
- Page 58 and 59: Electrical 2-35Section 2: Electrica
- Page 60 and 61: Electrical 2-37Section 2: Electrica
- Page 62 and 63: Electrical 2-39Section 2: Electrica
- Page 64 and 65: Electrical 2-41Section 2: Electrica
- Page 66 and 67: Electrical 2-43Section 2: Electrica
- Page 68 and 69: Electrical 2-45Section 2: Electrica
- Page 70 and 71: Electrical 2-47Section 2: Electrica
- Page 72 and 73: Electrical 2-49Section 2: Electrica
- Page 74 and 75: Electrical 2-51Section 2: Electrica
- Page 76 and 77: Electrical 2-53Section 2: Electrica
- Page 78 and 79: Electrical 2-55Section 2: Electrica
- Page 80 and 81: SECTION 3Installation Consideration
- Page 82 and 83: 3-2 Installation ConsiderationsSect
- Page 86 and 87: 3-6 Installation ConsiderationsSect
- Page 88 and 89: 3-8 Installation ConsiderationsSect
- Page 90 and 91: 3-10 Installation ConsiderationsSec
- Page 92 and 93: Trunk Mounting Considerations 4-1Se
- Page 94 and 95: Trunk Mounting Considerations 4-3Se
- Page 96 and 97: Trunk Mounting Considerations 4-5Se
- Page 98 and 99: Trunk Mounting Considerations 4-7Se
- Page 100 and 101: Trunk Mounting Considerations 4-9Se
- Page 102 and 103: Trunk Mounting Considerations 4-11S
- Page 104 and 105: Reference Information 5-1Section 5:
- Page 106 and 107: Reference Information 5-3Section 5:
- Page 108 and 109: Reference Information 5-5Section 5:
- Page 110 and 111: Reference Information 5-7Section 5:
- Page 112 and 113: Reference Information 5-9Section 5:
- Page 114 and 115: Reference Information 5-11Section 5
- Page 116 and 117: Reference Information 5-13Section 5
- Page 118 and 119: Reference Information 5-15Section 5
- Page 120 and 121: Reference Information 5-17Section 5
- Page 122 and 123: Reference Information 5-19Section 5
- Page 124 and 125: Reference Information 5-21Section 5
- Page 126: Reference Information 5-23Section 5
3-4 Installation ConsiderationsSection 3: Installation ConsiderationsPartition Installation <strong>Guide</strong>linesWARNING: The partition and the installation hardware of the partition must notinterfere with the proper operation of the safety belt, safety belt retractor, side impactsensor and the safety belt height adjusters. Failure to follow these instructions may resultin personal injury.WARNING: Installation of prisoner partitions may increase the risk of injury to frontseat occupants if the vehicle is impacted from a high speed rear end collision. This riskshould be balanced by the law enforcement agency against the risk of injury to the officerassociated with prisoner transportation. Failure to follow these instructions may result inpersonal injury.Safety Belt Retractor<strong>2007</strong> <strong>Police</strong> <strong>Interceptor</strong> <strong>Modifier</strong> <strong>Guide</strong>, 2006