2007 Police Interceptor Modifier Guide - Digital Ally, Inc.
2007 Police Interceptor Modifier Guide - Digital Ally, Inc. 2007 Police Interceptor Modifier Guide - Digital Ally, Inc.
Electrical 2-33Section 2: ElectricalHow To Change Option ContentLuggage Compartment Lid Release SwitchThe luggage compartment lid release system may be configured to operate either when theignition key is in the RUN/ACC position or at all times (without requiring a key). Configuration ofthe luggage compartment lid release switch is accomplished by connecting one of the 2 availableconnectors located behind the dash trim panel. One is wired for power at all times and the other iswired for power only when the ignition key is in the RUN/ACC position.2007 Police Interceptor Modifier Guide, 2006
2-34 ElectricalSection 2: ElectricalUse the following steps to change this option:• Remove the dash trim panel by gently pulling to release the 9 pushpin-type retainers.• Disconnect luggage compartment lid release switch electrical connector.• Locate and connect the alternate luggage compartment lid release switch electrical connector.Note: The connectors can be identified by the wire colors. The connector with the (VT/YE) and(BK/WH) wires has power at all times. The connector with the (VT/YE) and (YE/GN) wireshas power in the run position.• Reinstall the dash trim panel.Courtesy Lamp Disable (Dark Mode)This option offers deletion of the illuminated entry function. Upon vehicle power-up, the lightingcontrol module (LCM) will not provide interior lighting during entry or exit of the vehicle. Theinterior lighting will, however, still operate on demand whenever the dome lamp switch is active. Ifthe dark car feature is necessary, the assembly plant enables this feature through the LCM. Thevehicle can be reconfigured by entering diagnostics, enabling/disabling the courtesy lamps andthen exiting diagnostics.Use the following steps to enable or disable the courtesy lamps:1. Connect the vehicle communication module (VCM) and integrated diagnostic system (IDS)software with appropriate hardware, or equivalent scan tool to the data link connector (DLC).2. Select the LCM PID ‘‘COURTESY LAMPS’’.3. Select ENABLE or DISABLE.2007 Police Interceptor Modifier Guide, 2006
- Page 8 and 9: General Information 1-5Section 1: G
- Page 10 and 11: General Information 1-7Section 1: G
- Page 12 and 13: General Information 1-9Section 1: G
- Page 14 and 15: General Information 1-11Section 1:
- Page 16 and 17: General Information 1-13Section 1:
- Page 18 and 19: General Information 1-15Section 1:
- Page 20 and 21: General Information 1-17Section 1:
- Page 22 and 23: SECTION 2ElectricalContentsSection
- Page 24 and 25: Electrical 2-1Section 2: Electrical
- Page 26 and 27: Electrical 2-3Section 2: Electrical
- Page 28 and 29: Electrical 2-5Section 2: Electrical
- Page 30 and 31: Electrical 2-7Section 2: Electrical
- Page 32 and 33: Electrical 2-9Section 2: Electrical
- Page 34 and 35: Electrical 2-11Section 2: Electrica
- Page 36 and 37: Electrical 2-13Section 2: Electrica
- Page 38 and 39: Electrical 2-15Section 2: Electrica
- Page 40 and 41: Electrical 2-17Section 2: Electrica
- Page 42 and 43: Electrical 2-19Section 2: Electrica
- Page 44 and 45: Electrical 2-21Section 2: Electrica
- Page 46 and 47: Electrical 2-23Section 2: Electrica
- Page 48 and 49: Electrical 2-25Section 2: Electrica
- Page 50 and 51: Electrical 2-27Section 2: Electrica
- Page 52 and 53: Electrical 2-29Section 2: Electrica
- Page 54 and 55: Electrical 2-31Section 2: Electrica
- Page 58 and 59: Electrical 2-35Section 2: Electrica
- Page 60 and 61: Electrical 2-37Section 2: Electrica
- Page 62 and 63: Electrical 2-39Section 2: Electrica
- Page 64 and 65: Electrical 2-41Section 2: Electrica
- Page 66 and 67: Electrical 2-43Section 2: Electrica
- Page 68 and 69: Electrical 2-45Section 2: Electrica
- Page 70 and 71: Electrical 2-47Section 2: Electrica
- Page 72 and 73: Electrical 2-49Section 2: Electrica
- Page 74 and 75: Electrical 2-51Section 2: Electrica
- Page 76 and 77: Electrical 2-53Section 2: Electrica
- Page 78 and 79: Electrical 2-55Section 2: Electrica
- Page 80 and 81: SECTION 3Installation Consideration
- Page 82 and 83: 3-2 Installation ConsiderationsSect
- Page 84 and 85: 3-4 Installation ConsiderationsSect
- Page 86 and 87: 3-6 Installation ConsiderationsSect
- Page 88 and 89: 3-8 Installation ConsiderationsSect
- Page 90 and 91: 3-10 Installation ConsiderationsSec
- Page 92 and 93: Trunk Mounting Considerations 4-1Se
- Page 94 and 95: Trunk Mounting Considerations 4-3Se
- Page 96 and 97: Trunk Mounting Considerations 4-5Se
- Page 98 and 99: Trunk Mounting Considerations 4-7Se
- Page 100 and 101: Trunk Mounting Considerations 4-9Se
- Page 102 and 103: Trunk Mounting Considerations 4-11S
- Page 104 and 105: Reference Information 5-1Section 5:
Electrical 2-33Section 2: ElectricalHow To Change Option ContentLuggage Compartment Lid Release SwitchThe luggage compartment lid release system may be configured to operate either when theignition key is in the RUN/ACC position or at all times (without requiring a key). Configuration ofthe luggage compartment lid release switch is accomplished by connecting one of the 2 availableconnectors located behind the dash trim panel. One is wired for power at all times and the other iswired for power only when the ignition key is in the RUN/ACC position.<strong>2007</strong> <strong>Police</strong> <strong>Interceptor</strong> <strong>Modifier</strong> <strong>Guide</strong>, 2006