2007 Police Interceptor Modifier Guide - Digital Ally, Inc.
2007 Police Interceptor Modifier Guide - Digital Ally, Inc. 2007 Police Interceptor Modifier Guide - Digital Ally, Inc.
General Information 1-17Section 1: General InformationNote:During extended periods of vehicle storage (60 days or more) gasoline may deteriorate dueto oxidation. This can damage rubber and other polymers in the fuel system and may clogsmall orifices. A commercially available gasoline fuel stabilizer (Sta-Bil or equivalent)should be added to gasoline-powered vehicles whenever actual or expected storageperiods exceed 60 days. The manufacturer’s instructions packaged with the product shouldbe followed. The vehicle should then be operated at an idle speed to circulate the additivethroughout the fuel system.New Vehicle Storage — TiresMost high performance tires are made with nylon overlay.As such, the following steps should be taken to avoid flat spotting when the vehicles are not usedfor a period of time.• Store the vehicles with 44 psi in the tires. If the cars are to be driven, the air pressure should bereduced to recommended operating pressure and then increased back up to 44 psi whenreturned to storage.• If the vehicle is stored for periods longer than 30 days, it should be moved several feet at leastonce during each 30-day period, so that a different portion of the tread contacts the ground.Bumper HeightsAfter vehicle modification, the front and rear bumper heights must be verified to comply withFMVSS/CMVSS Part 581 and Ford specifications. Prior to determining bumper heights, themodified vehicle must be at curb weight. (See Engineering Guidelines, General Information, WeightDistribution Section for definition of Curb Weight.) Bumper heights are determined as follows:• Place the vehicle on a level surface.• Place the transmission selector lever in the PARK position.• Turn OFF the ignition and exit the vehicle.• Measure the vertical distance from the floor surface to the bottom of the front bumper structuralbeam (not the bumper fascia surface) at points 211 mm (8.3 in) to the left and to the right of thecenter of the bumper beam.• Measure the vertical distance from the floor surface to the bottom of the rear bumper structuralbeam (not the bumper fascia surface) at points 650 mm (25.6 in) to the left and to the right ofthe center of the bumper beam.• Record these measurements.Note:A maximum of 13 mm (0.5 in) side to side difference in bumper height is allowed.If the bumper heights are not within specification, the front springs must be changed to achievecompliance.2007 Police Interceptor Modifier Guide, 2006
1-18 General InformationSection 1: General InformationCrown Victoria Bumper Heights (at curb weight)Front Rear Tolerance394 mm (15.5 in) 389 mm (15.3 in) +/-25 mm (1 in)2007 Police Interceptor Modifier Guide, 2006
- Page 4: General Information 1-1Section 1: G
- Page 8 and 9: General Information 1-5Section 1: G
- Page 10 and 11: General Information 1-7Section 1: G
- Page 12 and 13: General Information 1-9Section 1: G
- Page 14 and 15: General Information 1-11Section 1:
- Page 16 and 17: General Information 1-13Section 1:
- Page 18 and 19: General Information 1-15Section 1:
- Page 22 and 23: SECTION 2ElectricalContentsSection
- Page 24 and 25: Electrical 2-1Section 2: Electrical
- Page 26 and 27: Electrical 2-3Section 2: Electrical
- Page 28 and 29: Electrical 2-5Section 2: Electrical
- Page 30 and 31: Electrical 2-7Section 2: Electrical
- Page 32 and 33: Electrical 2-9Section 2: Electrical
- Page 34 and 35: Electrical 2-11Section 2: Electrica
- Page 36 and 37: Electrical 2-13Section 2: Electrica
- Page 38 and 39: Electrical 2-15Section 2: Electrica
- Page 40 and 41: Electrical 2-17Section 2: Electrica
- Page 42 and 43: Electrical 2-19Section 2: Electrica
- Page 44 and 45: Electrical 2-21Section 2: Electrica
- Page 46 and 47: Electrical 2-23Section 2: Electrica
- Page 48 and 49: Electrical 2-25Section 2: Electrica
- Page 50 and 51: Electrical 2-27Section 2: Electrica
- Page 52 and 53: Electrical 2-29Section 2: Electrica
- Page 54 and 55: Electrical 2-31Section 2: Electrica
- Page 56 and 57: Electrical 2-33Section 2: Electrica
- Page 58 and 59: Electrical 2-35Section 2: Electrica
- Page 60 and 61: Electrical 2-37Section 2: Electrica
- Page 62 and 63: Electrical 2-39Section 2: Electrica
- Page 64 and 65: Electrical 2-41Section 2: Electrica
- Page 66 and 67: Electrical 2-43Section 2: Electrica
- Page 68 and 69: Electrical 2-45Section 2: Electrica
1-18 General InformationSection 1: General InformationCrown Victoria Bumper Heights (at curb weight)Front Rear Tolerance394 mm (15.5 in) 389 mm (15.3 in) +/-25 mm (1 in)<strong>2007</strong> <strong>Police</strong> <strong>Interceptor</strong> <strong>Modifier</strong> <strong>Guide</strong>, 2006