CNMAN003 Certificate III in Engineering (Locksmithing) - Training ...

111 Attachment H CNMAN001CNMAN003ATTACHMENT HSTREAM SPECIFIC INFORMATIONFORCERTIFICATE III IN ENGINEERING(MECHANICAL)ANEW LOCKSMITHINGSPECIALISATION WITHINMECHANICAL STREAM UNDERCNMAN003Certificate III in Engineering (Trade)FrameworkCNMAN001, CNMAN003 Version July 1999© TAFE Qld, State of Queensland Page H1

222 Attachment H CNMAN001CNMAN003NOTE:The following pages contain the competency Standard Unit listing that could beachieved for the finalisation of the stream. Where relevant standards cannot beidentified to meet the Competency Standard model required by the enterprise, theprovider, in consultation with the employer and ITAB may seek to customise thequalification from other NTP’s using the guidelines contained within the Metal andEngineering NTP Policy document.FoundationCompetenciesENGINEERING TRADESPERSON - LOCKSMITHTRAINING STRUCTUREThe Training Pathway will be made up in the following mannerFOUNDATION COMPETENCIES COMPULSORY Zero pointsUnits Points Description1.1F 0 Undertake interactive workplace Communication1.2F 0 Apply principles of OH&S in work environment1.3F 0 Apply quality procedures1.4F 0 Plan to undertake a routine taskCORE BAND 1 COMPETENCIES COMPULSORY – 20 PointsField Unit PoinDescriptiontsQuality 2.1C12 2 Apply quality systemsCommunication 2.2C11 2 Organise and analyse informationWork Organisation 2.3C11 2 Operate in a work based team environmentTraining 2.4C11 2 Assist in the provision of on the job trainingMeasurement 2.5C11 2 Measure with graduated devicesPlanning 2.6C10 4 Plan a complete activityComputations 2.7C10 2 Perform computations-basicComputations 2.8C10 2 Perform ComputatonsComputerApplications2.9C10 2 Perform Computer operationsCNMAN001, CNMAN003 Version July 1999© TAFE Qld, State of Queensland Page H2

444 Attachment H CNMAN001CNMAN003Field Unit Points Description Pre- requisitesLocksmith 20.6A 2 Maintain/Install doorcontroldevices2.5c11 Measure with graduated devices9.1A Draw and interpret a sketch.9.2A Interpret technical drawing.12.3A Precision mechanicalmeasurement.18.1A Use hand tools.18.2A Use power tools/hand heldoperations.18.3A Use tools for precision work.18.6ADismantle/repair/replace/assemble andLocksmith 20.7A 6 Repair andserviceautomotivelockingsystemsLocksmith 20.8A 2 Identifyautomotivesecuritydevices andgain entryLocksmith 20.9A 4 Indentify,repair andservice fireand securitycontainersLocksmith 20.10A4 Gain entryandreinstatementof fire andsecuritycontainers.fit engineering components.2.5c11 Measure with graduated devices9.1A Draw and interpret a sketch.9.2A Interpret technical drawing.12.3A Precision mechanicalmeasurement.18.1A Use hand tools.18.2A Use power tools/hand heldoperations.20.1A Establish Legal Possession20.1A Establish Legal Possession20.7A Repair and service automotivelocking systems2.5c11 Measure with graduated devices9.1A Draw and interpret a sketch.9.2A Interpret technical drawing.18.1A Use hand tools.18.2A Use power tools/hand heldoperations.20.1A Establish Legal Possession5.7A Manual heating, thermal cutting andgouging.5.12A Perform routine manual metal arcwelding.20.1A Establish Legal Possession20.7A Repair and service automotivelocking systemsNote selection of a Training Pathway including Pre-requisites is dependent uponadherence to the guidelines contained within the Metal and Engineering NTP Policydocument.CNMAN001, CNMAN003 Version July 1999© TAFE Qld, State of Queensland Page H4