LBB 1965/00 Plena Message Manager - WES Components

More documents

Recommendations

Info

Plena Message Manager | Installation and Operating Manual | Operationen | 21• Briefly press one of the pushbuttons (9), e.g. #11. The corresponding trigger indicator LED (8) will flash and the(upper) trigger indicator LEDs 1 to 6 will indicate the stored zones for pushbutton #11. The message indicatorLEDs (7) will only indicate the messages related to pushbutton #11. Their place in the sequence is not indicated.• Use the pushbuttons (9) to toggle the zones 1 to 6 ON and OFF, thus indicating the new zone selection.• Press the monitor pushbutton (3) briefly to clear the present message sequence for the selected pushbutton (9).Pressing the monitor pushbutton (3) once more causes the message indicator LED #1 to flash; subsequent pressingcauses the message indicator LEDs #2, 3, 4, etc. to flash. If the monitor pushbutton is pressed for more than3 s the message indicator LED that flashed is selected as the first message of a new sequence for the selectedpushbutton (9). In this way up to four messages can be selected in a random order to be part of that announcement.After the fourth message no more messages will be accepted.• Press the program mode pushbutton (4) once again for more than 3 s to enter the new configuration data and toexit the program mode.• Repeat the above procedure for any of the other pushbuttons (9).• If during this manual editing process a trigger input is activated, the unit will quit the program mode and therequested announcement will be started.• If in the program mode no pushbutton is pressed for approx. 25 s, the unit will automatically resume its normalworking mode, without storing the new configuration data.Bosch Security Systems | 2003-09 | 9922 141 50502en
Plena Message Manager | Installation and Operating Manual | Technical dataen | 225 Technical data5.1 ElectricalMains voltage230/115 Vac, ±10%, 50/60HzMax mains power consumption50 VAMax mains inrush current3 A @ 230 Vac / 6A @ 115 VacBattery voltage 24 Vdc, +20%/-10%Max battery current1 A5.2 MessagesData formatwav-file, 16 bit PCM, monoSupported sample rates (fs)24 kHz, 22.050 kHz, 16 kHz, 12 kHz, 11.025 kHz, 8 kHzFrequency response @ fs = 24 kHz 100 Hz - 11 kHz (+1/-3 dB@ fs = 22.050 kHz 100 Hz - 10 kHz (+1/-3 dB)@ fs = 16 kHz 100 Hz - 7.3 kHz (+1/-3 dB)@ fs = 12 kHz 100 Hz - 5.5 kHz (+1/-3 dB)@ fs = 11.025 kHz 100 Hz - 5 kHz (+1/-3 dB)@ fs = 8 kHz100 Hz - 3.6 kHz (+1/-3 dB)Distortion< 0.1% @ 1 kHzS/N (flat at max volume)> 80 dBMemory capacity8.38 MByte EEPROMRecording/playback time500 s @ fs = 8 kHz - 167 s @ fs = 24 kHzMax number of messages 12Supervision EEPROMcontinuous checksum controlSupervision DAC1 Hz pilot toneData retention time> 10 years5.3 InputsLoopthrough audio input 1 (3-pin XLR, balanced)SensitivityImpedanceCMRRLoopthrough audio input 2 (Cinch, unbalanced)Sensitivity1 VImpedance20 kOhm1 V20 kOhm> 25 dB (50 Hz - 20 kHz)5.4 OutputsSupervision pilot toneLine output 1 (3-pin XLR, balanced)Nominal levelImpedanceLine output 2 (Cinch, unbalanced)Nominal levelImpedance20 kHz, ±10%, level adjustable1 V, adjustable< 100 Ohm1 V, adjustable< 100 OhmBosch Security Systems | 2003-09 | 9922 141 50502en
Page 2 and 3: 2 | LBB 1965/00 Plena Message Manag
Page 4 and 5: Plena Message ManagerenInstallation
Page 6 and 7: Plena Message Manager | Installatio
Page 14 and 15: 3 15 427 63 8 15 42Input 1 Priority

LBB 1965/00 Plena Message Manager - WES Components

Create successful ePaper yourself

Delete template?

Save as template?